WHAT IS ON YOUR JUNK YARD WATCH LIST?

[5-90]

I've got a couple housings, but you'll want to get them retubed. They're both set up for FS Dodge PU front.

5-90

 

[Clean Racing]

The ZJ 44 is aluminum, it uses the same bearings/seals as a D35, not to mention very low aftermarket support.

-Mike

Wrong... The Alum 44 uses the same bearings as the ford 8.8... I know I have rebuild a ton of em... There is nothing wrong with them when you get the preload set properly...

 

[Mike L]

Wrong... The Alum 44 uses the same bearings as the ford 8.8... I know I have rebuild a ton of em... There is nothing wrong with them when you get the preload set properly...

UM, I had some in my shop before and they used the same as the Dana 35. This is going back to the ZJ stuff, unless the WJ is different. WTF do I know anyway. :shocked:

-Mike

 

[big black xj]

i need the vaccuum connector for the transfercase.It has 4 vacuum hoses comming out of it.All i need is the rubber connector.Mine got soaked with tranny fluid and stretched out so it doesnt hold a vaccuum.I think from 92 and older had the 231 w/vaccu crap.

 

[GSequoia]

It's best just to delete that connector block man, from both the axle end and the transfer case end. If you fine one that doesn't leak it WILL. Just snip it off and use short lengths of rubber hose to mate the plastic line to the goods.

 

[MogifiedXJ]

Some of the movable vent glass windows for the front.

 

[Mike L]

I forgot to add I need a clean hood, preferably white. Thanks.

-Mike

 

[5-90]

That will take a little longer, but I'm going to take a hood off of an 89 that I just picked up for parts, and transplant it onto my 88 (it has vents.) If you're interested, perhaps we could work out a swap?

BTW - did you get my PM on AW4 pans?

5-90

 

[Cherikon]

Looking for:

Stock rear tire carrier mounting brackets- upper interior (the one that is riveted in place) and the lower bumper one (that mounts inside the bumper)-

I will probably be going to the SD yards on Labor Day (it's 1/2 off!!!!) so I will be on the lookout, but the OC yards are better by far.:sunshine:

L8,
Coullt

 

[johnnyc]

I need a 97+ passenger side front flare.

 

[rpraterxj]

I need a 97+ passenger side front flare.

I got one off of my 2000. It's silver, but if you want it, let me know.

I actually have all 4!

 

[cracker]

I just realized I need a exhaust pipe that goes from the header pipe to the cat for a 94 HO.

 

[Andy Steiner]

I need a 97+ driver's side power seat frame. Dunno if there's a difference between connectors for heated seat or not, but I do have a heated seat.

Would also like a 97+ rear hatch. White if at all possible.

 

[Mr.OverKill]

bump stop / blocks from a 2000 ranger FX4X4 pick up truck

 

[cracker]

bump stop / blocks from a 2000 ranger FX4X4 pick up truck

I thought you wanted a 14 bolt and a front Dana 60 :dunno:

 

[Mr.OverKill]

I thought you wanted a 14 bolt and a front Dana 60 :dunno:

i do but in the mean time i figure that i should keep building my junk right.

 

[Mr.OverKill]

cj or tj folding side mirrors

 

[Gerr]

I just realized I need a exhaust pipe that goes from the header pipe to the cat for a 94 HO.

if its the same on a 95 I have one

 

[Gerr]

I want to play.

1. HP D30...

got one make offer

 

[goXJ]

header & head pipe for 99 xj (from the header to the cat.)

replacing a cracked banks torquetube.