- Location
- Harrisburg, NC
Not all of us can afford 60's Glenn.... 
Weekend is over...what did you get done?
- Thread starter Mr.Shrek
- Start date
sam24th
NAXJA Forum User
- Location
- charlotte NC
Not much done since school started again for me and already have been swamped with work. But I got new tires and wheels for my DD yota.
stumpXJ
NAXJA Forum User
- Location
- Atlanta, Georgia
That Currie high 9 thing was a joke...that's almost $4500.00 for two of them.
- Location
- Camden, SC
Yea I would hope so.... So what is the plan?
stumpXJ
NAXJA Forum User
- Location
- Atlanta, Georgia
Plan for what? Its a Hi Nodular case now, one of the strongest there is and still be a stock 3rd member. Im running it like it is until I need to address anything with it. If it breaks, ill fix it with something better. But for now, its got a full spool, fresh bearings and 4.56 gears. Makes no sense not to run it. Yeah, the pinion is a little low, but its only an inch or so lower than the 8.25 I was running. Its a WHOLE lot more axle than what I had, and so far its cost me $zero dollars.
- Location
- Camden, SC
Sweet! I did not realize the 8.25 was only an 1" higher. Mine was not an N case. I was just bustin your chops. I think its sweet.
shortxjdoug
NAXJA Forum User
- Location
- Chattanooga tn
Plan on buying shafts... They are a lot weaker than most people think. The n cases are pretty stout I don't see I going soon. It will eat 31 spline shafts as often as you feed them in, if your foot gets heavy
stumpXJ
NAXJA Forum User
- Location
- Atlanta, Georgia
I was thinking of buying some Moser 31 spline 5x4.5/5x5.5 shafts anyway, so I may end up doing that. Time will tell, im easy on my junk though. Atleast for now.
shortxjdoug
NAXJA Forum User
- Location
- Chattanooga tn
If you keep your current wheel and tire combo it should be fine....once you get in the heavy 37's even alloy 31 spline shafts go pretty quick
stumpXJ
NAXJA Forum User
- Location
- Atlanta, Georgia
Yeah, I figure once I go over 37's ill be at full 1 tons anyway. Thats phase 3 of the build.
- Location
- Columbus, In
Not much done since school started again for me and already have been swamped with work. But I got new tires and wheels for my DD yota.
Gonna have to say that yota is sweet dude!
- Location
- Harrisburg, NC
It's a pretty sweet truck. I've not seen it in a while to see some of his new additions.
- Location
- Columbus, In
Don't see them like that up here.
- Location
- on the beach in Ocean View, VA
- Location
- Harrisburg, NC
Not as quick as I promised, but I finally got it cleaned up for more than 5 minutes, and got home in time to do so before the sun went down.
Only thing i've done since I got it is tint the windows.
Love these seats
Couple more in here:
http://s840.photobucket.com/user/uncc_99xj/library/Focus ST
94xjsport94
NAXJA Forum User
- Location
- Carrollton, GA
Sold my ravines. Now what do I buy?
Lowrange2
NAXJA Forum User
- Location
- Abbeville, SC
JCR quarter guards with the tail light boxes. Then ship them to me.
DaveS98
NAXJA Forum User
- Location
- Chattanooga TN
Re: Re: Weekend is over...what did you get done?
I like the orfab ones with the bar better
I like the orfab ones with the bar better
stumpXJ
NAXJA Forum User
- Location
- Atlanta, Georgia
Buy shocks!
Lowrange2
NAXJA Forum User
- Location
- Abbeville, SC
I'd rather get JCR guards with the tail light boxes and add bars. The ORF ones don't have tail lights integrated.
This.
