who's ready and who's not?

85xjwoody said:
The shocks I have now are from a Rough Country 3" lift and they are way to long. If Ranger does not want to swap than I will give your shocks a try. Thanks Bob.

Kim.
Click to expand...

FWIW, I ended up using stock length shocks on my 8.8. They were pretty new off of our parts Jeep. I have plenty of travel with mine. I raised my mouts to the center of the tube, and I'm at 3 1/2 in the rear. Don't know if that info. will help any, but there you go.
 
Haleyes said:
FWIW, I ended up using stock length shocks on my 8.8. They were pretty new off of our parts Jeep. I have plenty of travel with mine. I raised my mouts to the center of the tube, and I'm at 3 1/2 in the rear. Don't know if that info. will help any, but there you go.
Click to expand...

I think that stock xj shocks would work for me but I don't want to buy new ones right now. Just some old used ones will work for now as long as I don't have the hard bottoming out anymore. I also welded my mounts flush with the tube and my springs gave me about 4.5"-5" of lift but still I have only about 2" of play in the shocks.

Kim.
 
seanR said:
The only thing I can say right now is,
"If it were easy, the women and children would be doing this!"

I an done for tonight!

Tomarrow is a brighter day!
Click to expand...
Well the front end is 99%.
I need to get a longer bolt for the right side where the tie rod and drag link join.

The rear....
Well I tore it apart again this eve.
Seems my spool is acting like an open diff.
the short side shaft isn't turning with everything else.
So the rear is back out and the shafts are pulled out and I am scratching my head.
The shaft is long enough, it goes clear into the spool.
They are not backwards the long side fully engauges and works fine just sticks out an inch.
I am puzzled!

I might be Jeepless!
Can I lead pink with the Super Duty?
 
85xjwoody said:
How many people are bringing firewood? Is there going to be enough? I can bring some if needed.

Kim.
Click to expand...
I have about a pickup load to bring, but we are much better off with too much wood than not enough. We may even want to get a couple of fires going. Bring whatever you can, it won't hurt a thing. :)

Les
 
seanR said:
Well the front end is 99%.
I need to get a longer bolt for the right side where the tie rod and drag link join.

The rear....
Well I tore it apart again this eve.
Seems my spool is acting like an open diff.
the short side shaft isn't turning with everything else.
So the rear is back out and the shafts are pulled out and I am scratching my head.
The shaft is long enough, it goes clear into the spool.
They are not backwards the long side fully engauges and works fine just sticks out an inch.
I am puzzled!

I might be Jeepless!
Can I lead pink with the Super Duty?
Click to expand...

was the spool stripped out?
jebus - i dont know...

Hey - if you have a stock open carrier, and nothing else works, we can install my aussie into your heep...

I did quite well yesterday open/open...
 
Last edited:
I'll be bringing about 6 bins of mixed hardwood scraps from my shop, to get those logs going good.
 
seanR said:
The rear....
Well I tore it apart again this eve.
Seems my spool is acting like an open diff.
the short side shaft isn't turning with everything else.
So the rear is back out and the shafts are pulled out and I am scratching my head.
The shaft is long enough, it goes clear into the spool.
They are not backwards the long side fully engauges and works fine just sticks out an inch.
I am puzzled!
Click to expand...
Eureka!
Any one have a short side shaft for a waggy rear 44 they would like to run over to my house today?
The one that is giving me troubles is only a 29 spline shaft.
it will not work.
I will go scrounging Monday to see if I can find something that will work.
Otherwise, I will be Jeepless.
 
I'm going to bring some wood also. Just in case. And I hope to have the rocker rails on tomorrow. Other than that, I'm ready.
 
seanR said:
Eureka!
Any one have a short side shaft for a waggy rear 44 they would like to run over to my house today?
The one that is giving me troubles is only a 29 spline shaft.
it will not work.
I will go scrounging Monday to see if I can find something that will work.
Otherwise, I will be Jeepless.
Click to expand...

29 spline? how many splines do they make a 44 shaft in? 27,30,33,35 and now we have proof of a 29....
 
I got my rear bumper finished today. Needs trimmed, painted and the shackles put on.

I'll bring half a MJ load of wood.
 
I'm bringing some firewood as well. JIM.
 
seanR said:
Eureka!
Any one have a short side shaft for a waggy rear 44 they would like to run over to my house today?
The one that is giving me troubles is only a 29 spline shaft.
it will not work.
I will go scrounging Monday to see if I can find something that will work.
Otherwise, I will be Jeepless.
Click to expand...
http://www.dutchmanms.com/4_axles.html

AMEX is our friend.
 
You must log in or register to reply here.

Similar threads

L
Torque Converter will not seat no matter what I do.
Replies
3
Views
1K
Legendaryfish35
L
macgyvr
Prizes for NAXJA members who pre-registered for Winterfest!
Replies
3
Views
142
REWSTER
REWSTER
J
2001 XJ Power Door Lock issue and battery drain
Replies
3
Views
363
Tim_MN
Tim_MN
S
Troubleshooting electric door locks on a 98
Replies
1
Views
242
SurplusFan98
S
macgyvr
***Trail Communications***
Replies
0
Views
104
macgyvr
macgyvr
Back
Top