- Location
- Nashville, TN
I'm going to Moab in the Morning!
Yeah, well, you can have your fancy Moab trip. I get to go to the Fall Flog!!!!!!!
Weekend is over...what did you get done?
- Thread starter Mr.Shrek
- Start date
Yeah, well, you can have your fancy Moab trip. I get to go to the Fall Flog!!!!!!!
XJsportG
SouthEast #4328 (RVA)
- Location
- Richmond, VA
Installed:
Clayton 4.5 Coils
RK UCAs
Serious 1-Ton UTK
Only problem now is steering is all jacked up..
Running 2 stabilizers ATM because of DW
Pictures here http://imgur.com/a/SUfEM#0
Clayton 4.5 Coils
RK UCAs
Serious 1-Ton UTK
Only problem now is steering is all jacked up..
Running 2 stabilizers ATM because of DW
Pictures here http://imgur.com/a/SUfEM#0
- Location
- Nashville, TN
6 likes behind a 2004 Dodge 3500 on a 6 inch lift. :dunno:
Lowrange2
NAXJA Forum User
- Location
- Abbeville, SC
I hit the like button for you! You can vote for me!
http://www.naxja.org/forum/showthread.php?p=245993321#post245993321
thechief86
NAXJA Forum User
- Location
- White House, TN
put rear disc brakes on my daily, and got my vw motor torn down for a rebuild.
found both heads are cracked, and I only have one spare good one. sucks to be me sometimes...
found both heads are cracked, and I only have one spare good one. sucks to be me sometimes...
Georgia Mike
NAXJA Forum User
- Location
- Flowery Branch,GA
Mounted the winch on my XJ. Funny part is that it's a Warn bumper and a Warn winch, but I had to modify the bumper to make it fit. I looked around the net to see what the issue was but I couldn't even find a pic of this bumper anywhere. It must be a pretty old design.
I had to cut a little on the passenger side to create enough room for the winch's motor heat sink. I think if it didn't have that it may have fit.
PLENTY of room on the other side
Nice tight fit
Plus I scored a factory gas tank skid for Wendy's ZJ at Pull-A-Part. Ever since the stories started coming out about fires after rear end collisions I've worried about it even though hers does have the factory-installed trailer hitch.
On that note I saw a fairly well-built XJ at the PAP Norcross location. It had a "XJ because anything else is a JoKe" sticker on the back window. Was that anyone on here?
I had to cut a little on the passenger side to create enough room for the winch's motor heat sink. I think if it didn't have that it may have fit.
PLENTY of room on the other side
Nice tight fit
Plus I scored a factory gas tank skid for Wendy's ZJ at Pull-A-Part. Ever since the stories started coming out about fires after rear end collisions I've worried about it even though hers does have the factory-installed trailer hitch.
On that note I saw a fairly well-built XJ at the PAP Norcross location. It had a "XJ because anything else is a JoKe" sticker on the back window. Was that anyone on here?
ChuckstrPT
NAXJA Member #791
- Location
- Birmingham, Alabama
I hear very good things about Choccolocco. My club's been out there. But my junk has been dead for over a year. I'm really looking forward to getting back in the saddle!
ChuckstrPT
NAXJA Member #791
- Location
- Birmingham, Alabama
I'm in.
- Location
- Camden, SC
Went to Chattanooga for a 25 year HS reunion. Watched football game with old friends Friday night, went out around Nooga after. Went to my old High School Saturday. Haven't been there in 10 years. Hiked a trail on Signal Mountain Saturday afternoon. Went to eh reunion Saturday Night. Drove the new to me diesel that and back. Over 700 miles on her this weekend. Ran like a top. Love that car's mileage.
- Location
- Nashville, TN
I vote for the 2014 Cherokee Crawl to be held in Moab!
94xjsport94
NAXJA Forum User
- Location
- Carrollton, GA
It's kind of either mild or wild, not much intermediate. I might be going back Saturday for this
I did some WJ swap stuff.
Any benefits to offset TRE's all the way around opposed to heims? I read all the stuff about clearance and droop but I already drilled out the knuckles lol
Also looking for the correct info on needing spacers on the caliper brackets and what not. I have the Teves calipers and am using 01 hubs with WJ rotors.
Lowrange2
NAXJA Forum User
- Location
- Abbeville, SC
I ran straight TREs. The only issue you'd have is diff cover clearance. It's close but should be fine. I ran a Solid Cover and it cleared with 1.5" DOM steering links.
With the 01 hubs you shouldn't need the spacer. Just look when install the caliper to be sure it's centered on the rotor.
94xjsport94
NAXJA Forum User
- Location
- Carrollton, GA
I might can get a bend in the tie rod if it is too close.
I didn't think I would but I'll have some in case I do. Hopefully doing this in 2 weeks. Need to order steering and track bar stuff and I should be good to go.
I didn't think I would but I'll have some in case I do. Hopefully doing this in 2 weeks. Need to order steering and track bar stuff and I should be good to go.
- Location
- Nashville, TN
There is a perfect leather interior for a 96 and older XJ at Express in Laverne. Red XJ in the row closest to the back fence.
Molly Ann
NAXJA Forum User
- Location
- Lafayette, IN
Much better than the crunched pile we left Harlan with!
- Location
- Nashville, TN
I got to spend about 5 hours yesterday driving around a 1965 Rolls Royce Silver Cloud III. What a fun car!
airman401
NAXJA Forum User
- Location
- Upstate, SC
Still working on this
- Location
- Harrisburg, NC
Finally making a little progress on the Jeep. Went to the junkyard today and scored an instrument cluster, as well as a stock e-fan to replace the aftermarket one that was in it and didn't fit worth a crap. Got the fan in nicely, the instrument cluster swapped (which seems to have eliminated the issue of the gauges coming back to life after shutting the Jeep off). Charged the battery up overnight, again, and was ready to run it today for a bit.
Going to leave the battery hooked up this week while i'm gone and see if it's still got a charge when I get home towards the end of the week. Hopefully this solves electrical drain i've been chasing...
Going to leave the battery hooked up this week while i'm gone and see if it's still got a charge when I get home towards the end of the week. Hopefully this solves electrical drain i've been chasing...
Georgia Mike
NAXJA Forum User
- Location
- Flowery Branch,GA
Got the tank skid put on Wendy's ZJ. Finished what I started two weeks ago and put the passenger side ball joints on my XJ. Then I took off the rear diff cover to see if I could figure out the source of the noise, and pretty much figured out it was just a botched setup job. Now I have to decide which fork in the road to take; rebuild it in the current configuration, or start fresh with something stronger. It's an 8.25" with full case Detroit & 4.10's, but it only has 27 spline shafts. Still trying to figure out why someone would spend big bucks on that locker and not swap to the 29 spline shafts at the same time 
For now I just buttoned it back up, threw in some fresh 85W-140 and it seemed to quiet it down, but I know it's just a band-aid and I'll need to address it sooner or later if I want to do anything other than trailer it when I need to go long distances.
For now I just buttoned it back up, threw in some fresh 85W-140 and it seemed to quiet it down, but I know it's just a band-aid and I'll need to address it sooner or later if I want to do anything other than trailer it when I need to go long distances.
Lowrange2
NAXJA Forum User
- Location
- Abbeville, SC
Worked, Wedding rehearsal, worked, wedding, worked, D35 to 8.25 axle swap.
Did this for a fella Jeeper that lives an hour up the road. Turned out pretty nice.
Now, he just needs to replace the t-case pinion seal.
Did this for a fella Jeeper that lives an hour up the road. Turned out pretty nice.
Now, he just needs to replace the t-case pinion seal.
Last edited:
