Lowrange2
NAXJA Forum User
- Location
- Abbeville, SC
Nice! I wish I had time to work on stuff like that.
Weekend is over...what did you get done?
- Thread starter Mr.Shrek
- Start date
jeepgeek2002
NAXJA Forum User
- Location
- Jax FL
**** i need a welder, tube bender, notcher.. etc. lol
Lowrange2
NAXJA Forum User
- Location
- Abbeville, SC
I got a few welders. Nothing fancy. I do need a bender and a notcher.
bigalpha
Moderator
- Location
- Tucson, AZ
Is it unreasonable to get 18 mpgs out of a 4.0L renix? I just calculated my mileage and it came out to 18.
stumpXJ
NAXJA Forum User
- Location
- Atlanta, Georgia
I get that on my non renix? You think its too high or too low?
Lowrange2
NAXJA Forum User
- Location
- Abbeville, SC
I get 16 out of my HO. 31s and stock gearing.
- Location
- Rainy side of Washington
Sounds pretty reasonable to me Alec. How'd you run those numbers - GPS or odo mileage? measured from full tank to full tank, right?
jeepgeek2002
NAXJA Forum User
- Location
- Jax FL
who's alec? isn't it Alek?
stumpXJ
NAXJA Forum User
- Location
- Atlanta, Georgia
This is just 3/4" tubing, so I used my Ridgid 368 Mechanical bender. Its a sweet little set-up, and does up to 180 degrees w/ 11 gauge (0.120") wall. This is 16 gauge wall.
I also got some 'practice' with the notcher this morning. 34 notches in all....
I also got some 'practice' with the notcher this morning. 34 notches in all....
- Location
- Rainy side of Washington
is it? crap. :dunce:
bigalpha
Moderator
- Location
- Tucson, AZ
I did it using the odo from tank to tank at the same pump. I thought it was too high. Good to hear it isn't. probably get Higher on the interstate.
And don't listen to that dummy. It's Alec.
And don't listen to that dummy. It's Alec.
jeepgeek2002
NAXJA Forum User
- Location
- Jax FL
:roflmao: :roflmao: :roflmao: :anon: :roflmao: :roflmao:
stumpXJ
NAXJA Forum User
- Location
- Atlanta, Georgia
Got it finished, painted and mounted...
ChuckstrPT
NAXJA Member #791
- Location
- Birmingham, Alabama
Got it finished, painted and mounted...
Dude, I need you to come over here and work on some of my projects....:viking:
- Location
- Gassaway TN
Stump, did you put that track on the roof for the basket to tie into or was it factory? I really need to add something to mine as well.
Last edited:
stumpXJ
NAXJA Forum User
- Location
- Atlanta, Georgia
Im not sure if it was factory or not Mark, but it was already on there when I got it. The cross bars on top have been VERY useful! The bars and track system is made by Yakima. I use the bars for all kinds of stuff, folding chairs, tables, strollers, etc. Works great!
stumpXJ
NAXJA Forum User
- Location
- Atlanta, Georgia
I fabbed up this Chainsaw holster/mount a while back and had it on my old trailer. The last two times we went camping, I have needed the chainsaw, but didnt have it. Now I will.
Holds it pretty darn tight, and protects the blade.
Of course, its lockable.
Bring on the Zombie Apocalypse!
Holds it pretty darn tight, and protects the blade.
Of course, its lockable.
Bring on the Zombie Apocalypse!
- Location
- Camden, SC
Sweet! Watched Justin Flop the Sami in Papa Gulch and Tfrady flop the xj on 3d! Good day today and added some moredents to the sheet metal! Also broke out the passanger rear window on Shipwreck.... about flopped it 2 or three times too! Good day with somegood friends!
jeepgeek2002
NAXJA Forum User
- Location
- Jax FL
I talked to lennie.. he was bragging about some hill climb? he said he almost rolled one time on that ravine trail? he sounded tired but seems as though he had a good time.
- Location
- Camden, SC
Yea the turn into Shipwreck.... he did not even ry it.
