- Location
- Camden, SC
Did you order yet? Is the weekend of the 17th good for some welding for you?
Weekend is over...what did you get done?
- Thread starter Mr.Shrek
- Start date
Did you order yet? Is the weekend of the 17th good for some welding for you?
Lowrange2
NAXJA Forum User
- Location
- Abbeville, SC
Yeah, I got $250 for the header panel and both fenders.
- Location
- Camden, SC
Dude you rape the poor bastard unless he needed that color.......
I think I have that priced out at $150 new.
- Location
- Harrisburg, NC
Not yet. I sent Andy an e-mail this morning to see if the bushings can be changed out for rubber ones later on down the road. Can't afford the rubber ones right now.
Weekend of the 17th is good for me.
Georgia Mike
NAXJA Forum User
- Location
- Flowery Branch,GA
Went to Mullins to install a dryer vent system for my mom. My brother in law was helping, and while we were under the house he accidentally bumped a water line. It busted and we basically took a shower while lying in the dirt. We got the dryer vent installed, then went to town for water pipe repair supplies, then it started raining when we got back. It was a wet, miserable day, but we got the job done and had a few good laughs in the process!
Georgia Mike
NAXJA Forum User
- Location
- Flowery Branch,GA
He probably sold them to Rodney haha
Lowrange2
NAXJA Forum User
- Location
- Abbeville, SC
The plastic aftermarket header panels are junk. A mint condition OEM header panel sells for $150 easy. $50 each on mint fenders. $250.
I wish. Good Ole' Rodney.
94xjsport94
NAXJA Forum User
- Location
- Carrollton, GA
Andy needs to hook me up with two calipers so I can use them as a core charge. Just tell someone you don't sell them with the axle for liability. Lol.
- Location
- Camden, SC
The plastic aftermarket header panels are junk. A mint condition OEM header panel sells for $150 easy. $50 each on mint fenders. $250.
I'm talking fiberglass.....
http://www.carparts.com/details/Jee...13&c2cid=0e47b44a-d344-4df6-9fdb-2158e8c19c40
http://www.discountbodyparts.com/ca...42&c2cid=92e7b098-6f03-4429-84f0-fb3b06a12bef
I was wrong on the fenders though. Looks like they are about $100 each.
Lowrange2
NAXJA Forum User
- Location
- Abbeville, SC
Oh, wow. I hadn't seen those prices before.
- Location
- Harrisburg, NC
Hope not. Because that means they'll be sitting at my house for a few months....
Lowrange2
NAXJA Forum User
- Location
- Abbeville, SC
Which reminds me. I had a guy message me this morning wanting to know if I had a D35 with ABS laying around that I'd be willing to sell...
Yes! ... Wait, no...
- Location
- Harrisburg, NC
It's been replaced with something much more beneficial to me...an 8.8
PAP in Winston-Salem may still have it...
- Location
- Camden, SC
That reminds me do you have spring perches?
- Location
- Harrisburg, NC
Have the full kit from Barnes sitting in my living room. Spring perches, shock mounts, u-bolts w/ hardware and u-bolt plates.
- Location
- Nashville, TN
Got a hatch strut ball off a ZJ at the junkyard yesterday. Used one of my old worn out ZJ struts and now my XJ has a gas strut lift hood. No more prop rod for me.
- Location
- Camden, SC
Sweet! SO unless something come up we will get that axle in on the 17th.
Lowrange2
NAXJA Forum User
- Location
- Abbeville, SC
Hmm, so the ZJ strut pivot dohicky bolts on?
- Location
- Middle Tennessee
Their stuff is beef. Mark was laughing about just the size of the U-bolts. They are huge compared to the stock 8.8 u-bolts.
- Location
- Harrisburg, NC
Sweet! May have to rig up the brakes a little bit. Meant to grab more of the parts off the donor exploder than I did, but I should be able to re-use what I have on the axle currently under it.
They are beef! And I got it for a pretty sweet deal too thanks to Black Friday deals!
