To-Do List

[dukie564]

Install rear locker
Redo Brake Lines
Install LCAs
Cut Fenders, Cut+Fold rear quarter panels
Install Flares
Pick up new(ish) tires
Install new trackbar
Install new springs
Install TC skid plate
Install new shocks
Install Disconnects for swaybar
slather copious amounts of di-electric grease around my engine bay
redneck alternator splash shield

aper:

 

[xcalibur223]

Guess I'll play..

Get spare tire
Swap over tire carrier.. might sell tire carrier for money to make it
Finish rear shocks through the floor.. Not gonna happen in time.. shocks in stock position for now
Order shocks for the rear.. not happening right now
Make some covers for where the uca and traction bar come through the floor
paint and put on D44 cover... done
CB radio
paint and install battery box
inspect, register, insure it

Adding on...
Put on front fender flares

 

[ROBZ95Xj]

only things im worried about now
Belly Pan
Cage
Fuel Cell pickups
New PS Pump

 

[dukie564]

Install rear locker DONE
Redo Brake Lines DONE
Install LCAs Waiting on grease bolts...
Cut Fenders, Cut+Fold rear quarter panels
Install Flares
Pick up new(ish) tires DONE
Install new trackbar
Install new springs
Install TC skid plate Partially done (damn you skidrow...)
Install new shocks
Install Disconnects for swaybar
slather copious amounts of di-electric grease around my engine bay
redneck alternator splash shield

aper:

 

[XJLI]

finish power steering stuff - good enough
install bumpstops - fronts done
install shocks - done
register and insure it - done
get wheels and tires - done
finish the cage/bumpers/etc - getting there..
get new pass side knuckle+ball joints - done and done
route front OX cable - done
tidy up rear brake lines - zip ties! done
trim gas tank skid so the 60 pumpkin doesnt smash it - barely makes contact, so done!
crossmember+skid - got one, its at sam's house :confused1
shorten front DS done, not balanced enough to do 60mph+ but whatev
install ZJ prop valve - done

added:
limit straps - measured, gotta order
put on new steering wheel
install new radiator + tranny and PS coolers

gotta keep adding tube and i'm good.. if i dont have a rear bumper thats fine but i want the front to be all done.

 

[foxwar71]

-Cut out floor and build subframe and skin it, relocate stock AW4 shifter - In progess, shifters mounted, seat mounts next
-Finish front half doors and trimmed for rockers - All doors mounted back up
-Build rear shock hoops, tie them together and to other stuff, mount shocks - DONE, just gotta add crossbrace
-Build rear bumpstop pads and mount poly bumps- DONE
-Finish painting the jeep with a brush
-Make rocker and belly skids, 1/8" plate + 1/2" plastic - Half done
-Some sort of seatbelts, probably just gunna run stock ones for now
-PSC hydro assist setup - Ordered
-Tiddy up brake plumbing and rebleed -
-Muffler heatshield/gas tank housing sheetmetal
-Maybe some shorter shackles - Nope
-Play with the StaK - Probably not
-Regrease/hit the instrument panel so my gauges will stay working again - DONE, bad ground
-Shakedown run and some thorough testing
-Try not to flop it, I'll wait til NACfest for that
-Acquire new tow rig possibly



:thumbup:

 

[ktm racer 419]

fix whatever breaks while im wheeling while you guys are still building.

well this seems to have changed...

chop up my frame

install front shock towers
install front shocks
brake hoses
chop up my frame
put my frame back together
chop up my bed
put my bed back together
take apart beadlocks and clean em up with new hardware
finish 14 bolt
install 14 bolt
figure out rear shocks
install all the fuel injection shit, including cell and whatnot.
figure out rear leafs, make new mounts.
new brakelines

and then theres the optional stuff...

fully box the frame
belly skid
rock sliders
traction bar
front bumper
hula girl on the dash.

 

[kastein]

Sounds like I'll be racing you on this one. I buy the rest of the metal for my frame soon and a doubler has entered the picture, because, well, I gotta build new driveshafts anyways...

Will it happen? I'll make that call when I have a few weeks left :laugh2:

 

[sheepjeep]

install front d44 - dont think this will be ready
install 8.8 - dont think this will be ready
some how make 37s fit - they will be mounted on wheels i hope by then
beef up steering - if the the donts not in then XXXX it
get tow rig - Done
get trailer - need to find one
registar - newlly added

 

[ktm racer 419]

well this seems to have changed...

chop up my frame

install front shock towers ten minutes
install front shocks ten minutes
brake hoses ten minutes
chop up my frame
put my frame back together half a day
chop up my bed
put my bed back together other half of that day going into night
take apart beadlocks and clean em up with new hardware ill do this in my spare time
finish 14 bolt couple hours
install 14 bolt couple hours including figuring out the pinion angle
figure out rear shocks shock hoops, an hour.
install all the fuel injection shit, including cell and whatnot. a good weekend.
figure out rear leafs, make new mounts. couple hours
new brakelines just gonna do the rear as the front is newish, half hour.

and then theres the optional stuff...

fully box the frame
belly skid
rock sliders
traction bar
front bumper
hula girl on the dash.

my goal is to have it "wheelable" by memorial day weekend. i need one uninturupted weekend to finish the frame chop and rear suspension shit, and another for the fuel injection, the rest is gravy.

i think the biggest pain in the balls will be chopping up the bed and getting it to fit again.

 

[kastein]

I added something to my list today, get a new tire or two (preferably two) since I slashed the crap out of one and my spare doesn't match.

Either that or go all out and aim to have 35s/37s on it by NACFest plus the axles, frame, etc. Not gonna happen...

 

[XJLI]

my goal is to have it "wheelable" by memorial day weekend. i need one uninturupted weekend to finish the frame chop and rear suspension shit, and another for the fuel injection, the rest is gravy.

itll be a good shakedown for both of us, i still havent done any real wheeling yet.

 

[Jeepman401]

Same here, i still need to get in a complete run

 

[RCman]

I see a lot of people that need to add "preregister" to their to-do lists.

C'mon folks! Less than 3 weeks remaining.

 

[MoparManiac]

- DONE Bend up harness bar and X brace for cage, finish weld and paint it (hopefully this weekend)
- Finish building 440
- DONE (surprisingly wasn't that bad haha) Get 440 to fit in engine bay :laugh:
- DONE - Build motor mounts
- DONE - Modify/ build crossmember, transmission mount, NP205 rear mount
- DONE - Redo traction bar crossmember mount (move to passenger side)
- FRONT DONE - Build new driveshafts
- DONE - Mount radiator, plumb cooling
- DONE - Build exhaust
- T-case shifters
- Center console and transmission tunnel
- Slave cylinder mounting/routing
- New dash and gauges
- Megasquirt and TBI
- Clean up wiring harness
- 241/205 DONE - Seal up/paint NP241/NP205/NV4500

Probably giving up on the t-case shifters and a nice dash for now. Just too much to do. I'll end up with just oil pressure/water temp hanging somewhere if I plan to make NACfest at all.

 

[ROBZ95Xj]

only things im worried about now
Belly Pan getting materials sunday
Cage aint gonna happen
Fuel Cell pickups ill just keep it full
New PS Pump just gonna toss in another used one

guuss i can add not to tear it up to bad memorial weekend

 

[foxwar71]

-Cut out floor and build subframe and skin it, relocate stock AW4 shifter - DONE
-Finish front half doors and trimmed for rockers - DONE
-Build rear shock hoops, tie them together and to other stuff, mount shocks - DONE
-Build rear bumpstop pads and mount poly bumps - DONE
-Finish painting the jeep with a brush - DONE
-Make rocker and belly skids, 1/8" plate + 1/2" plastic - Half DONE
-Some sort of seatbelts, probably just gunna run stock ones for now - DONE
-PSC hydro assist setup - DONE
-Tiddy up brake plumbing and rebleed - Somewhat DONE
-Muffler heatshield/gas tank housing sheetmetal
-Maybe some shorter shackles - Nope
-Play with the StaK - Nope
-Regrease/hit the instrument panel so my gauges will stay working again - DONE
-Shakedown run and some thorough testing - Next weekend
-Try not to flop it, I'll wait til NACfest for that
-Acquire new tow rig possibly



:thumbup:

 

[ktm racer 419]

install front shocks
chop up my bed
put my bed back together
take apart beadlocks and clean em up with new hardware
figure out rear shocks
install all the fuel injection shit, including cell and whatnot.
new brakelines

and then theres the optional stuff...

fully box the frame
belly skid
rock sliders
traction bar
front bumper
hula girl on the dash.


instead of being gay and putting "done" i just deleted the shit thats done.

 

[MoparManiac]

- DONE Bend up harness bar and X brace for cage, finish weld and paint it (hopefully this weekend)
- DONE- Finish building 440
- DONE (surprisingly wasn't that bad haha) Get 440 to fit in engine bay :laugh:
- DONE - Build motor mounts
- DONE - Modify/ build crossmember, transmission mount, NP205 rear mount
- DONE - Redo traction bar crossmember mount (move to passenger side)
- FRONT DONE - Build new driveshafts
- DONE - Mount radiator, plumb cooling
- DONE - Build exhaust
- T-case shifters
- Center console and transmission tunnel
- Slave cylinder mounting/routing
- New dash and gauges
- Megasquirt and TBI
- Clean up wiring harness
DONE - Seal up/paint NP241/NP205/NV4500

Instead of being gay and just deleting shit that I've done so everyone has to go back to see what I did, I put DONE in front of each thing I've finished.

 

[kastein]

instead of being gay like these guys I just fix what I need to make my truck drive and then drive it

and buy a bunch of things I don't need and will never install

I made money delivering parts with it yesterday and drove it today too