The Stupidist Jeep on the Planet

[5spd_xj]

ok thats fine too. Save my trailer fenders some carnage :laugh:

 

[ROBZ95Xj]

XXXX you! he's getting temp plates and driving this over

i wourld seriously consider it on travis's rollers

ok thats fine too. Save my trailer fenders some carnage :laugh:

it will be close, id like to atleast beable to drive around the field

 

[5spd_xj]

You can have the rollers, but one has a slow leak and ones got a gash/plug in the sidewall. If you have 2 good ones youll be in good shape :thumbup:

If not, the 4 of them would probably be fine, though i wouldnt count on the one with the leak to hold air enough to drive over then home again. Worst case you call for a rescue mission

 

[ROBZ95Xj]

You can have the rollers, but one has a slow leak and ones got a gash/plug in the sidewall. If you have 2 good ones youll be in good shape :thumbup:

If not, the 4 of them would probably be fine, though i wouldnt count on the one with the leak to hold air enough to drive over then home again. Worst case you call for a rescue mission

i already got 2 good rollers from ryan, they even have decent tread, he kept the crappy one

 

[ROBZ95Xj]

motor is ready to come out, gonna get a engine hoist tomorow then pull it after work

 

[ROBZ95Xj]

Ahhh wheres my motor!

there it is

next week it will get lots o goodies

rear main
oil pan gasket
valve cover gasket
spark plugs
cap
rotor
waterpump
t-stat
intake/exhaust gaskets
injector orings
Brown Dog block brackets and poly mounts
full cleaning of all the mud n oil
Cummins Biege paint
new flywheel and clutch
then mate ax15 to it for final time


also gonna clean all the dirt and leaves from the engine compartment, patch the rust spot under the batt tray and paint the engine compartment gloss black

 

[eflores]

Gay​

Ahhh wheres my motor!

there it is

next week it will get lots o goodies

rear main
oil pan gasket
valve cover gasket
spark plugs
cap
rotor
waterpump
t-stat
intake/exhaust gaskets
injector orings
Brown Dog block brackets and poly mounts
full cleaning of all the mud n oil
Cummins Biege paint
new flywheel and clutch
then mate ax15 to it for final time


also gonna clean all the dirt and leaves from the engine compartment, patch the rust spot under the batt tray and paint the engine compartment gloss black

 

[XJLI]

next week it will get lots o goodies

rear main
oil pan gasket
valve cover gasket
spark plugs
cap
rotor
waterpump
t-stat
garrett t3/t4 turbo
intake/exhaust gaskets
injector orings
Brown Dog block brackets and poly mounts
full cleaning of all the mud n oil
Cummins Biege paint
new flywheel and clutch
then mate ax15 to it for final time

FIFY

 

[Dundy]

FIFY

I see what you did there. You forgot the blow-off/re-circulatory valve.

 

[ROBZ95Xj]

managed to clean up the engine compartment a bit tonight

hopin to have it painted by the weekend, dont expect much to hapen next week as ill be stupid busy at work

 

[ROBZ95Xj]

got a late start this morning as it was a late night last night, got the motor on a stand, pulled lost of the stuff off it and tossed some paint on it, came out ok, oil pan will get painted seperatly and ill be putting a late model stamped steel cover on it, both will be matching Cummins Beige, all assc. brackets will be gloss black

wont have anything done till next weekend as im workin stupid hours at work this week

 

[eflores]

Still gay

 

[ROBZ95Xj]

motor gots some color now

gonna try and knock out more stuff after work tomorow and during the week, id like to have it back into the jeep late next week pending the arrival of some flywheel bolts

 

[MoparManiac]

that paint is blingin

 

[ROBZ95Xj]

got ac comp and alt back on, tomorow shall consist of cleaning intake and giving that some paint, then its just rear main and op gasket

 

[xj9140]

Should have painted it green...to match the motor stand

 

[ROBZ95Xj]

Should have painted it green...to match the motor stand

its a friends stand, last time i borred it he asked if i could paint it so i paited it an obnoxious florecent green

 

[ROBZ95Xj]

valve cover is on for final time, also picked up blingin chrome breather to replave broken one

also did rear main seal, oil pan is curently oil pan is off reciving paint, i may be spending a wee bit to much time on a motor that i dont expect to last longer then a year, for now i leave you with a pic of a yucky rotating assembly

 

[xj9140]

Hose that shit down with some WD40. I like the chrome breather but I dont think it will clear the hood. Maybe on the back of the valve cover it would but not the front. I could be wrong.

 

[XJLI]

your valve cover bolts is fancy