THe NAC Lots-O-BFG KO2 Thread

Re: THe NAC Lots-O-Post Thread

done and done

VJZx1kR.jpg
 
Re: THe NAC Lots-O-Post Thread

Dundy said:
My clutch pedal started to fade on the way home from work yesterday so I took a look under the truck: no leak. So i try to bleed the clutch this morning and all i get is a steady drip regardless of what the clutch pedal is doing. So I go to Auto Zone to get a new master cylinder (Betsy finds it hilarious that there's a master and slave cylinder). I go to put it in just to find that it was made wrong. It doesn't bolt to the firewall; it locks in (it's got a square hole in the firewall where the master enters. The master then rotates 45 degrees and locks in). Well they made it so when you lock it in the reservoir is at a 45 degree angle. Now I have to wait 'til tomorrow at 10 to get a different one. It couldn't have happened on a worse day (weather wise) this year. I'm psyched.
Click to expand...


45 DEGREES
 
Re: THe NAC Lots-O-Post Thread

kastein said:
You may not have read the whole post I was replying to but breathing the nasty shit formed when you arc weld on chlorinated chemicals (phosgene, chloramine, chlorine gas, elemental chlorine, ****yourshituporine, etc) is very very different from breathing some dicholoromethane or whatever. One kills you slowly, the other kills you all quick-like and very unpleasantly.
Click to expand...

Don't be a pussy dude just breathe it in. Don't believe everything you read on the internet.
 
Re: THe NAC Lots-O-Post Thread

Dundy said:
My clutch pedal started to fade on the way home from work yesterday so I took a look under the truck: no leak. So i try to bleed the clutch this morning and all i get is a steady drip regardless of what the clutch pedal is doing. So I go to Auto Zone to get a new master cylinder (Betsy finds it hilarious that there's a master and slave cylinder). I go to put it in just to find that it was made wrong. It doesn't bolt to the firewall; it locks in (it's got a square hole in the firewall where the master enters. The master then rotates 45 degrees and locks in). Well they made it so when you lock it in the reservoir is at a 45 degree angle. Now I have to wait 'til tomorrow at 10 to get a different one. It couldn't have happened on a worse day (weather wise) this year. I'm psyched.
Click to expand...

cut the splines, ramp it, smash it on with a hammer, then weld it
 
Re: THe NAC Lots-O-Post Thread

cut the splines, ramp it, smash it on with a hammer, then weld it, then break down in Moab, than shark fin it.
 
Re: THe NAC Lots-O-Post Thread

SHARK FIN
 
Re: THe NAC Lots-O-Post Thread

Processing deer is time consuming. Got some cooking to do this weekend. Going to grind a bunch of the meat and make stock for slow cooking out of the spine and ribs. The meat between the ribs was about 1/16" thick which is really too bad. I was hoping to smoke them like pork or beef. I think next time it will go a lot faster. Knowing what is where will help a lot.

Mmm venison burger for dinner was yummy.
 
Re: THe NAC Lots-O-Post Thread

We are hopefully going out again Saturday. If we get another one or two I'm sure I'll be giving some away.

I need a huge pot to boil the spine and ribs in to make stock. Any suggestions without spending an arm and a leg?
 
Re: THe NAC Lots-O-Post Thread

Any of you guys near Hunter, NY? My friends are getting married at a ski resort near there in May and I'm driving out with a couple other friends.
 
Re: THe NAC Lots-O-Post Thread

My mom has a 30 qt that will do.

I'm going to try to get another doe on Saturday. Fingers r crossed.

I didn't get home till midnight last night after processing all the meat with Mike. My alarm went off at 5am and I felt absolutely useless, so I called out because coming in an hour late means brutal Providence traffic. Got some shite to take care of around the house then I might head out again.

You know you're 'old' when sleeping till 730 is 2.5 hours more than you're used to.
 
Last edited:
You must log in or register to reply here.

Similar threads

R
Congratulations to our new Leadership!
Replies
2
Views
252
STROKER
STROKER
B
Looking for an passenger side OFFSET tie rod, 7/8-18 left hand thread offset to front of vehicle,
Replies
13
Views
344
Evan03
E
SAMSET
Check out the MWC Store on Breasy Things
Replies
2
Views
239
lesslimited
lesslimited
Bent
The BEST Medicine
Replies
7
Views
290
Nimrod
Nimrod
Jeepguy91
MWC election - Nominations for MWC Director at Large
Replies
3
Views
218
REWSTER
REWSTER
Back
Top