What did you do to your XJ today

[streetpirate]

got both of aaron barnes' opening vent windows installed without having to remove the door glass

 

[Scorpion8]

Got my passenger front power window regulator in from NAPA. Now just need time ....

 

[muddypunk]

Going to put my aal in today so I can clear the new shoes when I get the funds to buy them .Im gonna buy some 285/75/16 km2's

 

[hards91xj]

Got the new windshield put in .. Now it can rain.

 

[Scorpion8]

Got my passenger front power window regulator in from NAPA. Now just need time ....

Found the time, even in the rain. Installed it, works like a charm. Inside door skin and plastic barrier and trim need to go back in but the window runs up and down and I can lock it up without visqueen over the open window.

:thumbup:

Now, just gotta figure out WHY ALL the windows work from the master driver's window panel, but none work from their own up/down switches. Might be a short in the window lock button on the driver's door, or is there a fuse somewhere?

 

[muddypunk]

Well I took pic's but why post them I only gained 3/4 of an inch for stock eye leaf mad springs looked sad I didnt even realize how much sag I had :greensmok

 

[Scorpion8]

Now, just gotta figure out WHY ALL the windows work from the master driver's window panel, but none work from their own up/down switches. Might be a short in the window lock button on the driver's door, or is there a fuse somewhere?

FYI, fixed in another thread. Thanks!

 

[SHANE87]

I finnished my paintjob earlier in the week

tuesday I just riped out the plastic inner fenders up front

 

[SHANE87]

On tuesday I also used put my fender flares back on

When I roved the fenderflares all the studs that held them on broke so I used some 1/4in bolts that are 1in long with a rounded head that takes a philups so I dont have to worrie about them terring up my tires

 

[SHANE87]

And here are some pics I took wednsday of how it currently looks

 

[muddypunk]

We should hook up Shane I can push that huge dent out and make it look a little more happy looks good though I like the color :greensmok

 

[MCObray]

Replaced stock suspension with OME! BTW, didn't take it to a shop. A friend and I did the installation in his garage.

Getting an alignment tomorrow and then i'm good to go.

 

[muddypunk]

Nice looking rig =)

 

[SHANE87]

We should hook up Shane I can push that huge dent out and make it look a little more happy looks good though I like the color :greensmok

Hey man thanks glad to here you like the color. I will have to meet up with you one of these days to get your help with tat dent

 

[AwesomeXJ]

internet has been screwy and the phones been worse. anyways... the other day i replaced my stock sealed beams with halogens and discovered that the reason that the heep would stumble and stall when idling was because the map sensor vacuum line had melted closed. so i replaced the hard line with a rubber one. now its good to go. Yesterday I fabbed up some platess and welded them to my lower control arm mounts as skids.

 

[muddypunk]

So I had to see if I lost my flex with the new eye leaf aal this is what Ive got for rti lol

a shot of the leafs looking good ?

 

[AIbandit]

I cut another hole in my floor and put my fuel lines through my pretty grommet/floorboard. need to get some screws

Also installed my drive shaft.

my fuel pump wires are a hair short so I'm going to re run them tomorrow. Picking up some fuel tomorrow going to try to run her for a little bit.

 

[MCObray]

Picked up a brand new JCR Gas Tank skid for cheap!

[/IMG]

 

[MCObray]

Delete.

 

[kndrewa]

I put in new unit bearings today.
Also put in new sway bar bushings - but I got the wrong size.
28mm does not fit my swaybar.