- Location
- Bourbonnais IL.
Yea i pushed it to the floor and when it still wouldn't start after a lil bit i pumped the gas pedal and still nothing.
Important
- Thread starter bshaw
- Start date
Yea i pushed it to the floor and when it still wouldn't start after a lil bit i pumped the gas pedal and still nothing.
99SJ_Ex
NAXJA Forum User
- Location
- La Crosse, WI
Look back a couple pages, this is very similar to what happened to me... Check your intake/manifold bolts AND the manifold to down pipe bolts... Engine won't run if it can't build up back pressure.
Check your IAC and MAP sensors, check the rubber hose to the MAP sensor. Also check the Coolant Temp sensor and wiring, out their on the end of the block by all the heat will do weird things to them.
Check your IAC and MAP sensors, check the rubber hose to the MAP sensor. Also check the Coolant Temp sensor and wiring, out their on the end of the block by all the heat will do weird things to them.
- Location
- NE Indiana
Put a coil on it and drive it...
mac 'keep one in the glovebox' gyvr
mac 'keep one in the glovebox' gyvr
99SJ_Ex
NAXJA Forum User
- Location
- La Crosse, WI
This too, they like to heat crack on the side facing the block, from the heat.
I keep (new or used) an IAC, TPS, coil, and fuel injector in my tool box in back...
XJosh95
NAXJA Forum User
- Location
- Green Bay, WI
It sounds like it's getting some spark but no where near enough. I would suspect the coil, but popping off the distributor cap and looking at all the points can't hurt. They'll likely have some corrosion on them. Use a little bit of sandpaper to knock that off and clean up the points and the contact on the rotor, just may be enough of a fix to get you by until you put a new cap and rotor on it.
I call that a poor man's tune up & it has worked many times to get people by for a while.
- Location
- Columbus, In
Hey, don't worry about talking with the people on the shop floor when you move a machine. Now there is a clearance issue because they didn't talk to me.....Way to go guys! :doh:
I got bored this morning before work and started playing with the sheet of kydex I picked up. I bent this up and am planning on mounting it to the little area of the center counsel under the dash and next to my tcase lever. It is a lot better then letting it sit in my center counsel or under the seatbelt in my crossbreed while driving..
96'now I have to go to work and get some stainless hardware to mount it'2door
96'now I have to go to work and get some stainless hardware to mount it'2door
XJ&CHZ4ME
NAXJA Forum User
- Location
- Unionville, MO
I hang a gernade on my thingy.....
- Location
- Columbus, In
I got bored this morning before work and started playing with the sheet of kydex I picked up. I bent this up and am planning on mounting it to the little area of the center counsel under the dash and next to my tcase lever. It is a lot better then letting it sit in my center counsel or under the seatbelt in my crossbreed while driving..
96'now I have to go to work and get some stainless hardware to mount it'2door
That Kydex is some cool stuff. I usually stuff my XD between the console and passenger seat. Maybe I can whip something up to make an interchangeable holster for that. Spot. I haven't carried the XD since I got my LC9.
Customizer1000
NAXJA Forum User
- Location
- Ohio
Anyone around crawfordsville Indiana?
- Location
- Columbus, In
GoSlowGetStuck and Hubs97XJ(I think)
On an unrelated note. It sure is a pain in the ass to take someone else's kid to the Badlands. My 17 year old cousin is going with me this weekend and we have to have his dad fill out a form then have it notarized so he can go. Guess they gotta cover their bases though.
Customizer1000
NAXJA Forum User
- Location
- Ohio
Oh ok, working there in the am
altrocker1
NAXJA Forum User
- Location
- Iowa
are they vertical or horizontal shaft??? you could make a class project and build me a mud motor with that steel and one of those motors
here is one in a series showing what they look like:
http://www.youtube.com/watch?v=spLrxCfw_bM&feature=related
here is one at work
http://www.youtube.com/watch?v=nwlt4zr82KU
ive been contemplating building one for a while, but the steel fab is FAR beyond my skill level at this point.
- Location
- Bourbonnais IL.
my buddy tim had to have his wife sign a bunch of stuff because he as their stepfather was not allowed to take them.
- Location
- Bourbonnais IL.
my cap and rotor is what was bad on my jeep. running now
- Location
- Michigan
Easy button.
99SJ_Ex
NAXJA Forum User
- Location
- La Crosse, WI
are they vertical or horizontal shaft??? you could make a class project and build me a mud motor with that steel and one of those motors
here is one in a series showing what they look like:
http://www.youtube.com/watch?v=spLrxCfw_bM&feature=related
here is one at work
http://www.youtube.com/watch?v=nwlt4zr82KU
ive been contemplating building one for a while, but the steel fab is FAR beyond my skill level at this point.
Humm.... Interesting...
