- Location
- Camden, SC
The Brace:
Damages.....
- Thread starter Ghost
- Start date
- Location
- Camden, SC
Installed before the bumper went on.
- Location
- Middle Tennessee
Ok so last weekend I had a problem:
And this:
So now I'm here:
I know some guys who can make that crinkled sheetmetal straight again. I've seen them make it happen.
- Location
- Camden, SC
I bet! You intresed in that shop press?
- Location
- Middle Tennessee
Yeah, but how would I get it here?
shortxjdoug
NAXJA Forum User
- Location
- Chattanooga tn
- Location
- Camden, SC
I will get something figured out. Worse case I bring it to the Crawl this summer! LOL!
Yea I have to get it from the house first. Assuming the wife did not sell it to someone. LOL!
Anyone know if the header from a 84 will fit on a 94? If not the other thought was redkneck it up a bit and use the left over 4x8 sheet of 16 gauge I have in the shop and build something.
jeepgeek2002
NAXJA Forum User
- Location
- Jax FL
side note: Ghost stll looks bad ass!
- Location
- Camden, SC
Thanks but It's a FAT Biatch! I want to change the BS on the H1's and suck it in about 4" on the front. But that has to wait for a while. I wish Andy would move back to Concord then it would be Bad ASS! We would have some Ironman jeep build training days!
jeepgeek2002
NAXJA Forum User
- Location
- Jax FL
i need to order some stuff from him.. but right now.. i need to play catch-up on the truck payments..
- Location
- Camden, SC
In the course of my tear down to fix the front I found these: 
:bawl:
Starting to think I need to rethink things a little.
:bawl:
Starting to think I need to rethink things a little.
256offroad
NAXJA Forum User
- Location
- Huntsville Alabama
get the grinder out!!!!
The Hard Struggler
NAXJA Forum User
- Location
- Atlanta GA.
Just a flesh wound, drill it, weld it, and plate it.
- Location
- Camden, SC
Did not even do that much.... lol! Cleaned as best I could and welded it up. This one will get buggyfied when I find the cash for tube. I have most everying ready to go together. Once its all on I'll take it all off and paint it. I think I still have to weld some of the cross brace.
shortxjdoug
NAXJA Forum User
- Location
- Chattanooga tn
- Location
- Camden, SC
Ahh Hrew... you had me there. Last time I used 1.75 DOM. Andy has the bender so I have to get him here with it or me up there with my jeep and the steel. And judging on what he has done with the 5.9 I don't think I'll get him down here any time soon. I think he is trying to make the race at Winrock.
- Location
- Camden, SC
Talked to Andy this week. That is what he has been using on the ZJ. I'll have to see what is available around here.
Back to the repair that would not end....
New TB bracket.
Steering brace:
The bottom piece is the replacement TB I got from www.Ironman4x4fab.com!
Man I have a mess in the shop! I need to get this thing fixed so I can clean it up!
- Location
- Camden, SC
Insatalled it all on Saturday.... Little Glenn added the bling after work today:
Nice gaps:
Suck down winch plate is bent. I will be looking into that next.
Nice gaps:
Suck down winch plate is bent. I will be looking into that next.
Cnickgo
Do you need assistance?
- Location
- Monterey, CA
Wow thats cheap... a bumper or two starts sounding pretty good!
shortxjdoug
NAXJA Forum User
- Location
- Chattanooga tn
