WTB/Trade: Stock Suspension

[SharkXJ]

While I am parting out my heep I gotta get it back on wheels to take to scrap, or have them come and pick it up, either way it needs to be on all 4's.

I need STOCK suspension:
Coils
Leafs
Upper and Lower Control Arms
Tie Rod (does NOT have to be straight)

And I will need a front axel - Just needs to be able to hold the wheels on.

Hit me up with what you got.

I don't want to spend a lot cause it's just gonna get scrapped so if there is a part you need that is still available lemme know.

~Mark

 

[5-90]

What year part-out? I may have some early stock stuff lying about...

 

[srmitchell]

I'll have a turdy 30 low pinion soon. And I have some coils.

 

[the_weirdo]

Mark, I am gonna try to hit the PnP this weekend. Let me know if you want me to grab anything for you.

 

[hiimmred]

What time frame are you looking at Mark? I picked up a complete front axle assembly (everything except control arms) from Lauren that I'll eventually be putting under my junk once I get the gears and lockers swapped in from my current one. Your welcome to my old stuff when I'm done....no charge brother!

 

[SharkXJ]

Sorry for not getting back to you guys sooner.

5-90: It's a 2001 and I think pretty much any year stock parts will work.

Sean: When are you heading back? I would love to grab the coils and the LP off ya.

Josh: Thanks man I have some folks who have stepped up with some Free / Cheap parts. Call me or text while you are there and lemme know what they got.

Ed: I want ot have the Jeep out of the garage and gone by Thanksgiving weekend. I put up a butt load of Christmas decorations and I can't do that while the junk is in the garage. No room to bring crap down and so on. THANKS for the stuff even if I can't take any of it

 

[srmitchell]

I'm coming back for thanksgiving. I can try my best to do the swap before then.

The low pinion is free. Don't care.

Coils too.

 

[Johnnie Walker]

I might be getting some new leafs soon, if so my stockers are yours!

 

[SharkXJ]

Thanks guys.....

 

[XJensen]

I will be swapping out my LP 30 this winter as well. Just need to get things moving and get it geared. If I end up getting it done before anyone else its yours, but I am not sure when I will get it done.

I have a high clearance stock tie rod you can have. It comes with a 6" bend
I also have hubs from a pre 97, discs and calipers you could have. I believe they are 3/16" shallower and would all need to be used together. I have some front shafts you could have, although I am sure you are not worried about the bearings going to the JY.
I could look around if you need anything else. not sure if I have anything else though.

Josh

 

[the_weirdo]

Mark, I think I got the upper control arms laying in dirt at my old man's house. I'll go grab those and drop them off.

 

[SharkXJ]

I will be swapping out my LP 30 this winter as well. Just need to get things moving and get it geared. If I end up getting it done before anyone else its yours, but I am not sure when I will get it done.

I have a high clearance stock tie rod you can have. It comes with a 6" bend
I also have hubs from a pre 97, discs and calipers you could have. I believe they are 3/16" shallower and would all need to be used together. I have some front shafts you could have, although I am sure you are not worried about the bearings going to the JY.
I could look around if you need anything else. not sure if I have anything else though.

Josh

Josh:
Would you be willing to meet me half way for some of these parts? The hard part is figuring out when. I am pulling the Tranny on Saturday so maybe after that Saturday afternoon? Or maybe the 22nd? Are you going to be at the Toy Run in Hollister?

I don't need the hubs, callipers or shafts I have a ton of that crap lying around.

 

[SharkXJ]

Thanks to Josh (the_weirdo) I now have UCA's and Stock Shackles.

All i need now is:
Tie Rod (Pending Josh)
Leafs
Coils
LCA's
D30 - it can be bear, I have shafts and old unit bearings I can use.

Lemme know what ya got and we can set up somet ime for me to come and get it.

Thanks again,
Mark
Thanks again

 

[XJensen]

The tie rod is yours. bummer is I was in Tracy last weekend. I may be able to meet you depending on when. Shoot me a PM and let me know.

I am not going to make it to Hollister but may someone is that can run it down?

Josh

 

[blondejoncherokee]

if youre selling your jeep to a jy you dont need a front or rear axle on the thing. i know from experience. i made a sled outta 2x4's i had lying around and used a bunch of sand to tow the old xj outta the gargage. i got like 80$ instead of 140, you need to make sure they bring a flatbead.

 

[blondejoncherokee]

it was picknpull that i used though. not sure about other jy's

 

[MaxxXJ]

i got the LCA's and coils laying around here would of had the leafs too but i made a bastard pack with them

if ya got some 33's or 31's or know where i can find 4-5 that would help me out too

 

[AJTorris]

why are you selling it to a JY? What condition is it in?

 

[AJTorris]

do you have any pics of it?

 

[5-90]

You want to come over this week-end and pick up the leaves? Or I can possibly drop them by, if I can pry loose some boot space and I do some running about (gotta contact someone about getting pinion bearings pressed off to make setup bearings...)