xxmidianxx
NAXJA Forum User
- Location
- Spring, Tx
Re: What was done to YOUR rig today?
I am lucky... With mine being an 86, I have very few torx bits.
I am lucky... With mine being an 86, I have very few torx bits.
What was done to YOUR rig(XJ/MJ) today MECHANICALY????
- Thread starter ExTankerGuy
- Start date
magimerlin
NAXJA Forum User
- Location
- Flatonia, Tx
Re: What was done to YOUR rig today?
Tried to fix the welded up water pump mounting hole.:gonnablow:gonnablow:gonnablow
Didn't work
so you can see my wanted add in the for sale section about needing an engine block.....And no you cannot drill though it. I tried that and tried welding a stud to the cast block(yes I preheated it)
Tried to fix the welded up water pump mounting hole.:gonnablow:gonnablow:gonnablow
Didn't work so you can see my wanted add in the for sale section about needing an engine block.....And no you cannot drill though it. I tried that and tried welding a stud to the cast block(yes I preheated it)
eflores
NAXJA Forum User
- Location
- Greg's place
Re: What was done to YOUR rig today?
i have one id bring you for super duper cheap if i could talk that guy out of the 98 ish that needs a head gasket.....i need manche parts
i have one id bring you for super duper cheap if i could talk that guy out of the 98 ish that needs a head gasket.....i need manche parts
DeftwillP
NAXJA Forum User
- Location
- Round Rock TX
Re: What was done to YOUR rig today?
Might as well build a stroker while you're at it.
Might as well build a stroker while you're at it.
eflores
NAXJA Forum User
- Location
- Greg's place
Re: What was done to YOUR rig today?
i found out my new 29 spl 8.25 has a trash loc!
i found out my new 29 spl 8.25 has a trash loc!
magimerlin
NAXJA Forum User
- Location
- Flatonia, Tx
Re: What was done to YOUR rig today?
I do not have that type of money at the moment. Just need to get the dd on the road again so I can work on the Rig....
StylerG
NAXJA Forum User
- Location
- Oklahoma City
Re: What was done to YOUR rig today?
got my shackle relocation brackets in! Maybe i could get someone to burn them in before ROM...
got my shackle relocation brackets in! Maybe i could get someone to burn them in before ROM...
wheelinscott
NAXJA Forum User
- Location
- Ogden
Re: What was done to YOUR rig today?
cut and folded my lower quarters and cut the bumper to look better with it.
cut and folded my lower quarters and cut the bumper to look better with it.
eflores
NAXJA Forum User
- Location
- Greg's place
Re: What was done to YOUR rig today?
put the intake and exhaust back on lisa's it runs AMAZING but leaks out the rear main
put the intake and exhaust back on lisa's it runs AMAZING but leaks out the rear main
StylerG
NAXJA Forum User
- Location
- Oklahoma City
Re: What was done to YOUR rig today?
well i pb blasted my shackle bolts to make sure they would be ready to go for installing my shackle relocation brackets-they are good to go now i just need to find someone to help me weld them up before i install them...
also re-installed the front bumpstops and looked at where im going to try and trim the flares!
well i pb blasted my shackle bolts to make sure they would be ready to go for installing my shackle relocation brackets-they are good to go now i just need to find someone to help me weld them up before i install them...
also re-installed the front bumpstops and looked at where im going to try and trim the flares!
Art101
NAXJA Forum User
- Location
- San Antonio, TX
Re: What was done to YOUR rig today?
yesterday we put in my new leaf springs to get rid of the block that i had... now my rear end set up is 4.5" rough country springs and 1.5" teraflex shackle... whole reason for doing this was to cure my axle wrap issues. not sure that its going to work... after we finished working on our junk me and my buddies took off to go eat at chilis and one of my friends was following me in his car and said when i took off he could see my axle wrap up a little bit... and i drive like a grandma so this is bad!
yesterday we put in my new leaf springs to get rid of the block that i had... now my rear end set up is 4.5" rough country springs and 1.5" teraflex shackle... whole reason for doing this was to cure my axle wrap issues. not sure that its going to work... after we finished working on our junk me and my buddies took off to go eat at chilis and one of my friends was following me in his car and said when i took off he could see my axle wrap up a little bit... and i drive like a grandma so this is bad!
DeftwillP
NAXJA Forum User
- Location
- Round Rock TX
Re: What was done to YOUR rig today?
I replaced my rustys uca's with wj uca's in an attempt to fix my low caster issues. It does feel a lot better now but not perfect. Don't have an angle finder so I can't measure it. The funny thing is that I added caster which in most cases will make your pinion angle worse. I seem to have lessened 60+ mph vibes now.
For those interested: it's 6" of lift with trailmaster drop brackets and rustys fixed lowers.
I replaced my rustys uca's with wj uca's in an attempt to fix my low caster issues. It does feel a lot better now but not perfect. Don't have an angle finder so I can't measure it. The funny thing is that I added caster which in most cases will make your pinion angle worse. I seem to have lessened 60+ mph vibes now.
For those interested: it's 6" of lift with trailmaster drop brackets and rustys fixed lowers.
x2elite
NAXJA Forum User
- Location
- Texarkana, AR/TX
Re: What was done to YOUR rig today?
Which shackle locators did you buy, that require welding???
Which shackle locators did you buy, that require welding???
StylerG
NAXJA Forum User
- Location
- Oklahoma City
Re: What was done to YOUR rig today?
justin-got the hdoffroad ones like you have they require welding correct???
also just got done trimming the front fenders so i dont crunch another one (hopefully) didnt have enough time for the rear so those will have to wait a couple weeks
justin-got the hdoffroad ones like you have they require welding correct???
also just got done trimming the front fenders so i dont crunch another one (hopefully) didnt have enough time for the rear so those will have to wait a couple weeks
*whiteXJ*
NAXJA Forum User
- Location
- Wichita falls TX
Re: What was done to YOUR rig today?
got a new one today !!!
White 94 base model with 110k 2wd soon to be 4wd $400! new ac new battery straight body needs two font fenders NO RUST! and security system! go pick it up today! PICS soon
got a new one today !!!
White 94 base model with 110k 2wd soon to be 4wd $400! new ac new battery straight body needs two font fenders NO RUST! and security system! go pick it up today! PICS soon
Texas Twitch
NAXJA Forum User
- Location
- Plano, TX
Re: What was done to YOUR rig today?
pics or it didn't happen!!!
congrats bro!
pics or it didn't happen!!!
congrats bro!
Swamprat
NAXJA Forum User
- Location
- little Tijuana
Re: What was done to YOUR rig today?
$10 says he either hits a ligthpole or flips it before he gets pictures up.
jk lets get some pics!
$10 says he either hits a ligthpole or flips it before he gets pictures up.
jk lets get some pics!
xxmidianxx
NAXJA Forum User
- Location
- Spring, Tx
Re: What was done to YOUR rig today?
I dropped off my DS to get it lengthened. Now I have to get another one and have it shortened.
I dropped off my DS to get it lengthened. Now I have to get another one and have it shortened.
