THe NAC Lots-O-BFG KO2 Thread

Re: THe NAC Lots-O-Post Thread

mini=man said:
Travis, want to drag a set of wheels along with you to Gretchens this weekend?
Click to expand...

I can most likely do that. I might be taking a ride up to the truck dealer after work tomorrow, I could grab them from your house on my way back maybe. I do have plans with Mia at like 8 though so I might be cutting it close. If I can squeeze in the slight detour though, I'd be fine with that. Or if you can somehow get the wheels to my house then I'll definitely have no problem bringing them there for you
 
Re: THe NAC Lots-O-Post Thread

I'll tell that little brat its okay if you're late.

Lmk, they're free to the dude but I can't make it this weekend. The Jeep keeps having more issues with it so it's getting parked until the 44 goes in and I fix the rear brakes.
 
Re: THe NAC Lots-O-Post Thread

XJLI said:
not looking forward to sitting at the dmv aftetr work... dumb.
Click to expand...

I paid someone I work with to go register my truck for me so that A) I didn't have to sit there, and B) I didn't have to find a place to park downtown :laugh:
 
Re: THe NAC Lots-O-Post Thread

mini=man said:
I'll tell that little brat its okay if you're late.

Lmk, they're free to the dude but I can't make it this weekend. The Jeep keeps having more issues with it so it's getting parked until the 44 goes in and I fix the rear brakes.
Click to expand...

alright. If it's alright with you I'll give you a call when I'm on my way back and let you know how I'm doing time-wise
 
Re: THe NAC Lots-O-Post Thread

vetteboy said:
The bearing was $44 and I did the machining of the tall hex nut myself. If someone wants to take this and run with it, I'd be glad to get rid of it cheap...just wanna see it go to good use. I believe it'll work on an XJ or a Durango box; the nut is the same 1-5/16" size.
Click to expand...

Chris, is there a time limit on when that "good use" needs to actually start? If so I think I could be interested.
 
Re: THe NAC Lots-O-Post Thread

kastein said:
Chris - you might know of something for this. I need to decode the output from a quadrature encoder and preferably would be feeding the signal direct to a PC / embedded system via i2c, SPI, or USB. Know of any off the shelf products for this? off the shelf angle sensors that decode straight from input shaft to i2c/spi/usb are also cool.
Click to expand...

What you're looking for is called a boner.
 
Re: THe NAC Lots-O-Post Thread

mini=man said:
I'll be here all night buddy.

Mind me asking why you;re going back up there?
Click to expand...

When I bought the truck there was no spare under the bed, and part of the verbal agreement was that they'd get one for me. I said I didn't care if it was a used tire and a steel wheel- I just want to have something. But when I picked it up they had forgotten about it. So he just said to swing by sometime next (now this) week and in the meantime he'd scrounge one up. I've been busy every night but I want to try and make sure I've got it for this weekend, only because according to Murphy's law, since I'll be towing that'd be the time I'd get a flat :laugh:
 
Re: THe NAC Lots-O-Post Thread

cmelo said:
What you're looking for is called a boner.
Click to expand...
I already have one of those and it's not really going to fit into a USB port
 
Re: THe NAC Lots-O-Post Thread

Steering leak fixed :thumbup: still binding on the way to full right lock though. Added another washer between the box/frame and that didn't change anything. I'm definitely inclined to believe it's binding prior to the steering box itself so I'll just lure my buddy over here with beer tomorrow night and put him to work. He owes me a transmission swap after last weekend so he better not bitch about drinking my beer and turning the steering wheel. :D Now time to clean up and watch some hockey.
 
Re: THe NAC Lots-O-Post Thread

so apparently in 4 years i never had snap rings in my upper ball joints. and to get the ball joint out i had to cut the knuckle.

this just goes to show that snap rings are useless.

however i had to weld my lower ball joint in place on the new knuckle. it fit loosely
 
Re: THe NAC Lots-O-Post Thread

ktm racer 419 said:
so apparently in 4 years i never had snap rings in my upper ball joints. and to get the ball joint out i had to cut the knuckle.

this just goes to show that snap rings are useless.

however i had to weld my lower ball joint in place on the new knuckle. it fit loosely
Click to expand...
the set of chevy/fsj knuckles I just bought from Ben H didn't have the snap ring on the upper BJ either.

PS: never buying rust belt knuckles again. These ones are damn near rust free, the ones I bought from Colin are crusty as shit, the right one moreso than the left. Right one is so rusty I was almost afraid to put it on an axle till I compared actual metal thickness remaining to the rust-free set :roflmao:
 
Re: THe NAC Lots-O-Post Thread

Managed to get through to comcast and actually get my problems resolved quickly and in time to catch the end of the opening ceremonies and see the start of the game.

Doesn't make me hate comcast any less.
 
Are relays supposed to rattle like a bad lightbulb? I have no clue
 
Re: THe NAC Lots-O-Post Thread

Just had to stitch my XXXXing finger up, good thing I was already drunk, neighbor had some thread and a needle handy
 
You must log in or register to reply here.

Similar threads

R
Congratulations to our new Leadership!
Replies
2
Views
165
STROKER
STROKER
B
Looking for an passenger side OFFSET tie rod, 7/8-18 left hand thread offset to front of vehicle,
Replies
13
Views
254
Evan03
E
SAMSET
Check out the MWC Store on Breasy Things
Replies
2
Views
160
lesslimited
lesslimited
Bent
The BEST Medicine
Replies
7
Views
198
Nimrod
Nimrod
Jeepguy91
MWC election - Nominations for MWC Director at Large
Replies
3
Views
133
REWSTER
REWSTER
Back
Top