THe NAC Lots-O-BFG KO2 Thread

[xjbump]

Re: THe NAC Lots-O-Post Thread

Remember Irish today, hungover tomorrow.

 

[MoparManiac]

Re: THe NAC Lots-O-Post Thread

Bastard.

Reminds me, I need to order a new upper ball joint sleeve to fix the camber.

:roflmao:

Get your crap together so we can wheel.

 

[foxwar71]

Re: THe NAC Lots-O-Post Thread

Get your crap together so we can wheel.

Agreed.

 

[5spd_xj]

Re: THe NAC Lots-O-Post Thread

yeah mark!! you disgust me sometimes, with your lack of a wheelable rig....




:eyes:

 

[MoparManiac]

Re: THe NAC Lots-O-Post Thread

I'll make up for you guys' lost time

 

[5spd_xj]

Re: THe NAC Lots-O-Post Thread

you better...

 

[5spd_xj]

Re: THe NAC Lots-O-Post Thread

actually, don't. i appreciate the offer but i need all the incentive i can get to work on mine every chance i get!!! heh

 

[XBoBJ]

Re: THe NAC Lots-O-Post Thread

http://failblog.org/page/ these are pretty funnyyyyyyyy

 

[ROBZ95Xj]

Re: THe NAC Lots-O-Post Thread

No problem man. Like I said, I wish I could have made it a reality to have everyone there, but we'll always have runs.

BTW, did you get those edelbrock shocks as well?

no i orded a set of frt RE twin tubes for my Jeep and a set of monotubes for a friends theve been on backorder for a month

 

[ROBZ95Xj]

Re: THe NAC Lots-O-Post Thread

I do mine at home.

Tape measure is all you need for toe.

As long as your BJs and hub bearing assemblies are good you shouldn't have a problem with camber. Unless your housing/knuckles are bent.

ill give it a shot, right now the alighnment is still good but i willl be adding a extra set of factory coil isolaters wich may mess my alighnment a tad, then i gotta figure out the caster deal once i get the arms in

 

[Begster]

Re: THe NAC Lots-O-Post Thread

:roflmao:

Get your crap together so we can wheel.

Agreed.

Ugh, if I finally get my sheete together will you leave me alone? But seriously, hopefully it will be driving soon, just have to adjust the rear brakes, replace that steering box, and fix the damn trackbar once and for all.
I want to wheel too.

yeah mark!! you disgust me sometimes, with your lack of a wheelable rig....




:eyes:

Lack of drivable Jeeps is what you meant to say.
Both of them don't drive...
And I realize its funny because you don't have one either.

 

[cmelo]

Re: THe NAC Lots-O-Post Thread

 

[ROBZ95Xj]

Re: THe NAC Lots-O-Post Thread

got a whole lot of nothing done today on the jeep, got a lower control arm installed, a extra coil isolator on the drivers side installed and the trackbar removed, got a bad headache so time for bed

 

[ROBZ95Xj]

Re: THe NAC Lots-O-Post Thread

ok beer and advil fixed me headache, now im goin back out to work on the jeep more, now for a tech question, factory lower control arms are 15.75" the fixed re's i got are 16", now factory upper arms are 15" im thinking to set my adj upper re arms to 15.25, am i thinking corectly here or did i miss somthing

 

[ROBZ95Xj]

Re: THe NAC Lots-O-Post Thread

went to remove the pass lower control arm, axle bolt came right out, but frame bolt seems to be rusted to the bushing sleeve, so tomorow ill break out the angle grinder and cut it out

 

[billyjp2]

Re: THe NAC Lots-O-Post Thread

you're keeping this thread alive tonight rob

 

[5spd_xj]

Re: THe NAC Lots-O-Post Thread

*excuse me, excuse me...*


I'll take over thread-living duties for ya Rob, you're free to go.

 

[ROBZ95Xj]

Re: THe NAC Lots-O-Post Thread

no im wired right now, a 2 liter bottle of Coke will do that to you

 

[5spd_xj]

Re: THe NAC Lots-O-Post Thread

yes it will, indeed.

 

[5spd_xj]

Re: THe NAC Lots-O-Post Thread

seems like ya bounced right back from that headache no problem huh? haha