So Cal Karma 2008

[GrimmJeeper]

dang we got an OG rapper in da house!

sounds more like a pirate to me

 

[alek21]

sounds more like a pirate to me

hmm... ima stick with rapper lol

 

[paulhead]

1 very bald 33" MTR holds air

picture

4 30x9.5x15 mud rovers 1 bald, 1 cut, 3 hold air

 

[IslanderOffRoad]

Dana 30 disco housing. No gears, no shafts, no knuckles. Has a block off plate and the tube dremeled out for 1pc shaft conversion. Will not separate the block off plate, you must take the whole axle

Knuckles from a 99 XJ.

Stock steering from a 94 XJ

 

[djblade311]

Dana 30 disco housing. No gears, no shafts, no knuckles. Has a block off plate and the tube dremeled out for 1pc shaft conversion. Will not separate the block off plate, you must take the whole axle

Knuckles from a 99 XJ.

Stock steering from a 94 XJ

I'll take the knuckles...PM your addy

 

[paulhead]

I'll take the knuckles if you don't Josh.

 

[GrimmJeeper]

I'll take the knuckles...PM your addy

I'll take the knuckles if you don't Josh.

John is up in simi valley i believe. i'll offer my place up as a half way point they can be dropped off at if that helps either of you. he comes down this way somewhat often.

 

[IslanderOffRoad]

Josh and I are both in Big Bear this week, I'm gonna hand them off there.

 

[Skullver]

I'll take the knuckles if you don't Josh.

I'll take them if Paul and Josh don't

 

[89cherokeexj]

I'm ging to post this up on here again. I have 4 doors. Blue in color, no dents. The driver side door is missing the glass. I also have the hatch too! Need it out of my yard. There are no door panels, handles etc.

I still have these never heard back from the guy who wanted them..

 

[xDUMPTRUCKx]

Dana 30 disco housing. No gears, no shafts, no knuckles. Has a block off plate and the tube dremeled out for 1pc shaft conversion. Will not separate the block off plate, you must take the whole axle

Knuckles from a 99 XJ.

Stock steering from a 94 XJ

i could really use this!

you know the p/n for the seal?

 

[cal]

i could really use this!

you know the p/n for the seal?

Its setup to use a stock OEM seal.

You need to use a lot of RTV, it leaks just a little around the edges.

 

[Leep]

i could really use this!

you know the p/n for the seal?

Ben, CR11800 is the common seal that generally works. The best thing to do is measure then hit napa with the measurements.

The one I did on my green jeep was a little small and leaked a bit but the 2 that we did on the blue jeep and tims jeep worked fine.

 

[GrimmJeeper]

you know the p/n for the seal?

NAPA #11899 is what went into mine, we use CR part numbers.

Dennis, 11800 only fits a 71-72 international scout.. sure thats the right number?

 

[xDUMPTRUCKx]

very well then....thanks for the help guys!

ill take it!

 

[GrimmJeeper]

very well then....thanks for the help guys!

ill take it!

Same deal John, if you are in my area and can fit it in the honda, it can live at my house for a bit.

 

[xDUMPTRUCKx]

Same deal John, if you are in my area and can fit it in the honda, it can live at my house for a bit.

thatd be sweet!

 

[Leep]

NAPA #11899 is what went into mine, we use CR part numbers.

Dennis, 11800 only fits a 71-72 international scout.. sure thats the right number?

That is what I used in the first 2, maybe I will get the 11899, what is the outer diameter size difference, like 1/8" ?

I will order the 11899 and I also polished the shaft and used the outter disco seal just in case.

 

[GrimmJeeper]

11800# ID 1.8880" OD 2.0040" W 0.2500"
11899# ID 1.1920" OD 2.1280" W 0.3500"

big difference on the ID :dunno:

 

[Leep]

11800# ID 1.8880" OD 2.0040" W 0.2500"
11899# ID 1.1920" OD 2.1280" W 0.3500"

big difference on the ID :dunno:

Thanks Grimm