less then 2 months!!!!

Door rust is up by the mirror. I hope I don't have to redo it up there after Moab. All the painting I want/need to do is for rust prevention, not to win the show and shine.

The last show and shine I entered was the morning after the last time I went looking for a big section of mud to repeatedly run through. Needless to say, I didn't place :D .

Bones :skull1:
 
Bones said:
Here's the short list. Some aren't that important and time will tell if they actually get done, others are a bit more important.

Front gear install

Axle u-joints

Steering box

Front shaft balance

Rear springs – re-arch

Lock (keyless entry) pin switch

Lube including double Cardan

Hood vents

Anti-wrap ladder bar with rework of t-case skid

Limiting strap front

Re-set caster

Water wetter

Heat shield (intake)

Heat shield (cat)

t-case?

SBS install x2

Aux fan relay –remote power

Driver door rust

Headlight covers- paint/replace

Fog lights remove (and replace?)

Gauges and pod (tranny and A/F)

Tranny temp sending unit and header

gauge pod install

Headliner

Rock rails paint

Tire balance

Hood alarm switch

Replace rear exhaust clamp

Check diff fluids

Steering wheel

Front springs replace - done

Front susp paint – done

Hood vent drip system

Low oil pres light/buzzer



Bones :skull1:

Why rush it? As much as you enjoy wrenching in Moab, just work this stuff in between runs............:D
 
Why rush it? As much as you enjoy wrenching in Moab, just work this stuff in between runs............

thefinger.gif
Salute!
thefinger.gif


I would like to actually enjoy the fire side chats and stuff this year instead of warming myself by the halogen lamp set up to wrench into the night :rolleyes: .

Bones :skull1:
 
Bones said:
thefinger.gif
Salute!
thefinger.gif


I would like to actually enjoy the fire side chats and stuff this year instead of warming myself by the halogen lamp set up to wrench into the night :rolleyes: .

Bones :skull1:

Then don't drive. :scottm:
 
you mean ride into camp with him sticking out through my sunroof with a maglite guiding the way?

I think I still have the bruises :shiver:

Bones :skull1:
 
I need to find someone I can afford to set up my front gears, pack, gas up, kiss the dog and kick the wife, find something to keep the kid busy for 5 hours, pull outta the driveway!
50 days till lift off!! whooohoooo!
 
ouch a4x4..... that sucks... I just realized myself that I need to fix my two hookup for the camper :( I smashed the 7 pin plug harness and socket (stock hitch) on a rock... and even though I got one to replace it already (thanks Sequoia) I never have the time to get around to it....

Kejtar
 
jeeze! some of you complain about a mere weeknd's worth of work!

gotta design and build an entire front and rear suspension, on all new frame and axle brackets. install new steering, modify driveshafts, design and byild a new crossmember, skidplate, re-route new exhuast, brakelines, fuel lines, adapt e-brake cables on new bracket, add a few more tubes to the rollcage, and other various odds and ends......

and bones is compaining about door rust!
 
Make sure your mom does a lil more than tack welds w/ her 120 buzz box, K ? Boot to your lip

Chewy

PS: Did you find a pile outside your alley?
 
Kejtar said:
ouch a4x4..... that sucks... I just realized myself that I need to fix my two hookup for the camper :( I smashed the 7 pin plug harness and socket (stock hitch) on a rock... and even though I got one to replace it already (thanks Sequoia) I never have the time to get around to it....

Kejtar

Been there, done that, bought the t-shirt.....

My 7way plug comes off with 2 screws, and normally lives in the onboard toolbox when not towing. I have 2 4wire flat connectors, 1 from a T-tap style interface, and 1 that is custom wired for trailer brakes and 12V.

When it's off, there is nothing hanging down.
 
I think everybody should jump in here and say something to Beezil about remembering to have his mom weld everything :firedevil

The funny thing is that you all don't realize that his sister is the best welder in the family.
 
Back
Top