Junk Yard Parts Finds/Requests

[socalkid13]

Dana 44, gas tank skid, 97-01 rear hatch interior panel in grey

 

[sidewaysstarion]

Half off at ecology Wilmington today as well.

 

[rockclimber]

looking for front doors (4door) off a 97+ white preferred. (not dented)

 

[scottmcneal]

Why?Look at your avatar and think about it.I was there, i know how you drive.LOL

 

[rockclimber]

Why?Look at your avatar and think about it.I was there, i know how you drive.LOL

how I drive is exactly why... I'm looking for some not-dented ones that I can put on for going to the mall... and I can make a nice set of trail doors out of my dented ones for going to the trail.

 

[scottmcneal]

Now you're starting to sound like me.HaHa

 

[David_Bricker]

Dang, Sideways - I should have asked you to grab the entire front grill assembly off of that rig. It's all in far better shape than mine!

David Bricker / SYR

 

[sidewaysstarion]

I didnt know if a renix era front end would work for you, they has no post 90 xjs there.

 

[GSequoia]

I'd venture to bet it would but you would need the entire grille assembly including all trim from marker lamp to marker lamp. I don't know for sure but I'd imagine the fiberglass header panel is the same, I don't see why Chrysler would spend the money to re-engineer that.


Personally I prefer the Renix-era grille, instead of the simple three piece job of the HOs it has more, end result is the trim pieces on the top and bottom do not have that ugly seam at the headlamp doors.

 

[HA1RY DANGL3R]

Half off at ecology Wilmington today as well.

Did you pull the 44 or is it still sitting there?

 

[sidewaysstarion]

I didnt have the tools to pull it, so I left it there.

 

[HA1RY DANGL3R]

I didnt have the tools to pull it, so I left it there.

Thanks!

 

[travisk]

If anyone comes across an 8.8 axle from a Ford Explorer with a 4.10 ratio, please let me know.

The door tag code will be 42 or D2 and the axle itself may be tagged with 410 or 4L10. These seem to be somewhat rare. All of the ones listed on car-part.com are $500 or more. I'd rather find it in a yard for $130.

 

[garrett83]

If anyone comes across an 8.8 axle from a Ford Explorer with a 4.10 ratio, please let me know.

The door tag code will be 42 or D2 and the axle itself may be tagged with 410 or 4L10. These seem to be somewhat rare. All of the ones listed on car-part.com are $500 or more. I'd rather find it in a yard for $130.

Try the Sante fe springs ecology, I think I saw quite a few 8.8s there, I didn't pay attention to the gear ratios tho

 

[travisk]

Thanks, I will check out Ecology.

 

[travisk]

At the Santa Fe Springs Ecology today there were were 6 or 7 early XJ's, one green 96 XJ that was pretty much gutted and one MJ. There was one 8.25 and about 15 Explorer 8.8s, but they were almost all 3.73 limited slip.

 

[travisk]

There's a leather rear seat from a 91 that's in decent condition at the anaheim pick your part.

 

[PahlMc]

I'm looking for stock front and rear driveshafts for a 2001 XJ as spares. I'm never at the JY. I live near LAX now and moving to San Diego this summer. I'd gladly pay the JY Price and $40 for your time if you find them.

 

[David_Bricker]

No rush, but if anyone could pull me an intact front grill assembly, including headlight bezels, side markers, etc for a '95, I'd appreciate it. A bit too large to fit in my checked luggage.

David Bricker / SYR

 

[GSequoia]

Do you want the fiberglass header panel as well?