Important

With around 3" my 31s fit, just need bump stops. Also adjusted the stops on the knuckles to cut down on LCA rub

Sent from my HTC6525LVW using Tapatalk
 
If that is 3" lift equipment, once you mount those tires, my guess is they will only be around 30" tall so you'll be fine.

Mastercrafts run on the small side. Going to be a nice setup
 
chuck619120 said:
Some shiny new parts did show up at my house from the good folks at IRO:



I guess I have plans for this weekend. Hopefully if I put all these on I can fit these:



And keep my beloved factory plastic pieces. Any suggestions?
Click to expand...
I'm actually looking at getting these tires. Only 135 shipped, 10lbs lighter than mine and seem to have good reviews.

Sent from my HTC6525LVW using Tapatalk
 
Amazon prime. 2 day tire delivery. I was looking at your Goodyear but these are cheaper. For a wheeling rig I'd keep the Treadwright tires but for DD I want something litter and better wearing.

Sent from my HTC6525LVW using Tapatalk
 
need-a-bow said:
Amazon prime. 2 day tire delivery. I was looking at your Goodyear but these are cheaper. For a wheeling rig I'd keep the Treadwright tires but for DD I want something litter and better wearing.

Sent from my HTC6525LVW using Tapatalk
Click to expand...

Stay away from mastercrafts then. Buy a better tire if you are worried about wear. Or an AT.

Mastercrafts tires have been terrible since they changed over the the AXT ,MXT, CXT design. They will wear worse than your Treadwrights easily and they will be much louder on the road. if you don't rotate them every2-3k miles max you are going to hate them.
 
Before Josh chimes in, add for the day

e11e7bf102bdf639674d14ceb3dd06ed.jpg
 
csailors said:
Stay away from mastercrafts then. Buy a better tire if you are worried about wear. Or an AT.

Mastercrafts tires have been terrible since they changed over the the AXT ,MXT, CXT design. They will wear worse than your Treadwrights easily and they will be much louder on the road. if you don't rotate them every2-3k miles max you are going to hate them.
Click to expand...
I have the older A/T Treadwrights in a load range E on the Expy, them things wear like iron. They do flat spot a touch when it's really cold.

Sent from my SM-S920L using Tapatalk
 
BTaylor said:
I suggest cutting the factory plastic pieces.
Click to expand...

Shoot cutting plastic would just lead to cutting metal.

csailors said:
If that is 3" lift equipment, once you mount those tires, my guess is they will only be around 30" tall so you'll be fine.

Mastercrafts run on the small side. Going to be a nice setup
Click to expand...

The front coils are actually 4". The add a leafs are supposed to net 2". With my lift shackles and relocation boxes, I am hoping to match the 4". I do have an extra set of XJ springs, so I may add the main leaf to the mix.


csailors said:
Stay away from mastercrafts then. Buy a better tire if you are worried about wear. Or an AT.

Mastercrafts tires have been terrible since they changed over the the AXT ,MXT, CXT design. They will wear worse than your Treadwrights easily and they will be much louder on the road. if you don't rotate them every2-3k miles max you are going to hate them.
Click to expand...

I agree with all this. I would not have bought them except for 2 reasons. They were cheap ($400) and only had to drive 12 miles to pick em up. Secondly they are temporary since I plan on giving in and cutting some plastic (maybe metal too) to fit 33's by the end of summer.
 
You must log in or register to reply here.

Similar threads

1
New here, but not to Jeeps
Replies
1
Views
60
macgyvr
macgyvr
C
Delete my info
Replies
3
Views
126
Numbers
Numbers
A
Power window issues, all 4 were working but no longer
Replies
5
Views
275
maxbraketorque
M
S
Troubleshooting electric door locks on a 98
Replies
1
Views
192
SurplusFan98
S
Bent
The BEST Medicine
Replies
7
Views
193
Nimrod
Nimrod
Back
Top