XJ D30 & ChryCo. 8.25"

[2000xjclassic]

I am doing an axle swap so I will have my current axles up for sale out of my 2000 XJ

Front:
Low Pinion Dana 30 ~135k miles
Stock 3.55 gears
Aussie Locker XD-13027 (http://www.aussielocker.com/index.ph...-xd-13027.html) installed October 2008
Jcr Offroad one ton steering 1TNST (http://www.jcroffroad.com/Merchant2/...go ry_Code=S6) installed under the knuckle summer 2009.
Tube Seals AL 11103 (http://www.justdifferentials.com/ind...uct s_id=2487) installed April 2009
Lube Locker gasket. Installed april 2009
Timken Unit bearings.
New ball joints on driver side November 2009. I have the ball joint NIB for the other side, not installed. They are included or I can install them.
OEM axle shafts. One side has circle clips installed, I can install circle clips on the other shaft if the buyer plans on running the factory shafts.
I can also include an XJ High Pinion D30 with factory 3.55 Gears if the buyer wants to transfer parts over to a HP axle. The LP was never a big enough issue for me to swap everything over to the HP.


ChryCo. 8.25" 29 Spline
Factory 3.55 gears
Aussie Locker XD-58229 (http://www.aussielocker.com/index.ph...d-58229-2.html) installed January 2009
Factory Shafts
Factory Drums
Lube Locker Gasket LLR-C825 (http://www.justdifferentials.com/ind...uct s_id=2193) installed April 2009

Largest tire run on both axles was a 31x10.5, That was before either locker and both axles were mainly stock. The only tire ever run with the lockers was a 245/75r16. Most of the parts (lockers, steering, seals, etc) were installed since October 2008.

Both axles are still under my Jeep, but I am getting ready to pull them out soon and it is not my DD so they are available when ever. Axles are located in 44012 available for pick up. I will deliver for free with in a reasonable distance or further for some fuel money. I am also willing to ship on the buyers dime but I haven't found a good way to ship them with out it costing a ton.

I will also have the current lift on my Jeep available (I will make another thread for that)

 

[2000xjclassic]

I am building my Jeep so I am looking for trades too. (hydroboost/master cylinder, np231, D300, aw4, hydraulic assist stuff, let me know what you are willing to trade, worst I can say is that I'm not interested)

 

[85xjwoody]

Need some prices to go with the details.

 

[2000xjclassic]

Need some prices to go with the details.

Whoops. $800. I'm looking to trade/deal if you have something that I need for my build. so don't hesitate to ask or make an offer.

 

[butch cassidy]

would you separate? im very interested in those d30's. im about 30 minutes west of Cleveland and could be there asap.

 

[scoobyxj]

I got a NP231, and a AW4 from my 2000 I'm pulling parts from. They are already mated, and IIRC have around 115k on them. Tranny got a fluid/filter change (full flush with a machine) around 70k, and had a aux cooler on it from probably 90k on. 231 has synth oil in it. Both shifted perfect before it was wrecked, and wasn't abused. Would you be interested in a straight up trade for trade? I'm about 2hrs south of you too so logistics shouldn't be to much of an issue. Get at me back channel if you're interested. I got the motor too if you's happening to be looking.

 

[2000xjclassic]

PMs sent

 

[CONKLE73]

I’ll take the Aussie Lockers per our PM’s…

 

[AdamG8GXP]

Are the lockers sold?

 

[2000xjclassic]

Lockers sold. Still have the steering for the front along with the knuckles already set up for UTK. Both housings/carriers/gears. 1 set of ball joints NIB. shafts for the front and rear.