- Location
- Golden, CO
I see it now, that shock mount is at least an inch inboard, and three inches higher than stock mounts. I remember Tom Houston telling me he wished he'd retained the shock travel on his rig.
The Yeti
- Thread starter Kittrell
- Start date
time2getdirty
my cats breath smells
- Location
- Cheyenne, Wyoming
When I had flush mount lower shock mounts on my xj I had to go to a short body 8" shock and even then still had limited up travel. I ended up going to a lower hanging shock mount .
planefixer
NAXJA Forum User
- Location
- Colorado Springs, CO
When I moved my shock mounts up onto the axle I out boarded them as far as possible and ended up having to go with an 8" travel shock. A little more down travel would be nice but it works pretty decent.
- Location
- Golden, CO
I must not "wheel," I have yet to get hung up on the factory shock mount.
I can cut the mounts off that D-35 you gave to me...
I can cut the mounts off that D-35 you gave to me...
Last edited:
DutchVDub
NAXJA Forum User
- Location
- Milliken, CO
I actually have a set I cut off of an 8.25 sitting in my garage.
- Location
- Thornton, CO
Thanks for the offer guys. My front shocks are too long as well so I might as well just get a full set. Looks like I'll have to go with the 8" travel variety, at least out back.
Boostwerks.com
NAXJA Forum User
- Location
- Colorado
I should have a set of those sitting in my basement if you're interested? I'll take a look when I get home.
DutchVDub
NAXJA Forum User
- Location
- Milliken, CO
- Location
- Thornton, CO
You should upsell him on your rear shock towers.
Ha, no holes in my floor, thanks!
freerider15
NAXJA Forum User
- Location
- FoCo, Crawlorado
You got me wondering with my upcoming 8.8 swap.
However, I'll be running TNT U-bolt eliminators.
I plan on trying to outboard the axle side mount to nearly under part of the mount, i.e. a couple inches further toward the wheel than you have.
However, I'll be running TNT U-bolt eliminators.
I plan on trying to outboard the axle side mount to nearly under part of the mount, i.e. a couple inches further toward the wheel than you have.
trippled
NAXJA Forum User
- Location
- colorado springs, co
I used the mounts that came with my ruff stuff 8.8 kit. I out boarded the mounts so they straddle the inner u bolt. I think I have maybe 4-5 inches of shaft showing. I can tell it's using the majority of it but haven'tvent had any issues yet
- Location
- Thornton, CO
Any luck?
- Location
- Thornton, CO
Getting down to the wire on this pile. Rock sliders are supposed to deliver Thursday and a new heater control valve Friday. In the time is has sat my coolant bottle has run down to nothing. Finally got around to figuring out where it was going. Still need to put oil in the diffs, center/adjust the trac bar, mount the front bumper/modify the brackets and deal with the rear shock mounts. Really wanted some time to at least get one run in before I commit a week to driving it but what can ya do. Some of the beautification will have to come after COFest.
xj-grin
NAXJA Member #1096
- Location
- Colorado Springs, Colorado
looks nice, DJ.
- Location
- Thornton, CO
So the "grinding" that kept me from bringing the rig to COFest ended up being the muffler. With the rig loaded down for camping I lost enough lift height that the driveshaft was kissing it on every revolution. Annoyed that I wasn't able to see if the morning of, I probably could have BFH'd my way to Buena Vista.
The muffler was rusting through so it was on my list to replace anyways. I could not find anyone who has run this so I decided to give it a shot. I needed something considerably smaller than the stock muffler but I am not a fan of loud exhaust.
On this rare occasion the old stuff came right off and I had the new pieces on in about an hour start to finish. Plenty of clearance now and I am pretty content with the sound. It has a nice rumble to it but not obnoxious at all. Haven't tested it yet for drone on the highway but I took the RPM up and am confident it's not going to be an issue.
The muffler was rusting through so it was on my list to replace anyways. I could not find anyone who has run this so I decided to give it a shot. I needed something considerably smaller than the stock muffler but I am not a fan of loud exhaust.
On this rare occasion the old stuff came right off and I had the new pieces on in about an hour start to finish. Plenty of clearance now and I am pretty content with the sound. It has a nice rumble to it but not obnoxious at all. Haven't tested it yet for drone on the highway but I took the RPM up and am confident it's not going to be an issue.
- Location
- Thornton, CO
Picked up some other goodies as well. Valve cover/oil pan gaskets, rear main seal, new pcv stuff and a fan shroud. My old shroud was missing the top half of it. I've done the vc, shroud, and pcv stuff so far. Will get to the pan and seal at some point. It's got a pretty significant oil leak.
Oh and before and after on the rear wiper.
Oh and before and after on the rear wiper.
Last edited:
DutchVDub
NAXJA Forum User
- Location
- Milliken, CO
Eww, maintenance.
macgyver_7_6
NAXJA Forum User
- Location
- Mid Missouri
Where did you get your tailpipe? Do you have a part #? I haven't been able to find a nice piece without crappy pinched bends. Looks like yours is mandrel bent.
How do you like the flat flares? Been thinking of going that route.
Nice build!!!
How do you like the flat flares? Been thinking of going that route.
Nice build!!!
freerider15
NAXJA Forum User
- Location
- FoCo, Crawlorado
- Location
- Thornton, CO
Yep, that's it. Bought it straight from Holley as well, I did not see a lower price anywhere.
I do not hate them but I am not in love with the look either, I'm pretty particular though. They are a solid flare and cleanly open up your fenders front to back quite a bit. I would never pay the $400+ for them new though.
