THe NAC Lots-O-BFG KO2 Thread

Re: THe NAC Lots-O-Post Thread

DAMNIT. I so friggen wish I had my green jeep running right now so I could wheel this weekend.
 
Re: THe NAC Lots-O-Post Thread

Yes...that's it, somone must have hacked my account.
I would never say something like that, not cool.


I'm serious, I really wish I had my Jeep running right now.
 
Last edited:
Re: THe NAC Lots-O-Post Thread

-take rear axle apart and replace pinion and carrier bearings.
-make disk brake brackets fit, cut old bearings off axle shafts and press new ones on with new backing plates.
-replace hard brake lines that are rusted and about to blow
-strip paint/coating/LCA brackets off frame rails, weld on frame stiffeners.
-weld on Clayton brackets, combine clayton crossmember with TNT crossmember for awesomeness crossmember
-move axle forward/ make sure steering is no longer hitting trackbar bracket
-install rock rails
-see if drive line shop can balance rear driveshaft after I dented it.
-install travis's front bumper that I'm not giving him back.
-etc.
 
Re: THe NAC Lots-O-Post Thread

Begster said:
-install travis's front bumper that I'm not giving him back.
Click to expand...

:scared::scared::scared::scared::scared:


excuuuuuuuuuse me?!?! Check's in the mail I'm assuming? :laugh3:
 
Re: THe NAC Lots-O-Post Thread

keith, good news. i was able to drill out the breather. it's just a press-in deal.
 
Re: THe NAC Lots-O-Post Thread

i pulled my tcase in seemingly record time tonight too. maybe an hr and 45 mins from fully installed (with driveshafts) to fully out.
 
Re: THe NAC Lots-O-Post Thread

Begster said:
-take rear axle apart and replace pinion and carrier bearings. NOPE!!!
-make disk brake brackets fit, cut old bearings off axle shafts and press new ones on with new backing plates. 5 MINUTES!!!
-replace hard brake lines that are rusted and about to blow 8 MINUTES!!!
-strip paint/coating/LCA brackets off frame rails, weld on frame stiffeners. NOPE!!!
-weld on Clayton brackets, combine clayton crossmember with TNT crossmember for awesomeness crossmember NOPE!!!
-move axle forward/ make sure steering is no longer hitting trackbar bracket NOPE!!!
-install rock rails 12 MINUTES!!!
-see if drive line shop can balance rear driveshaft after I dented it. NOPE!!!
-install travis's front bumper that I'm not giving him back. W/E!!!
-etc.
Click to expand...
 
Re: THe NAC Lots-O-Post Thread

Yo Mark all you have is 25 minutes worth of work to do!? WTF hurry up and do it.
 
Re: THe NAC Lots-O-Post Thread

I really feel like we should have a meet and greet sometime soon. Maybe when my buddy order's his lift I can have a few of you guys come up and give us a hand. $$$ is a possibillity.
 
Re: THe NAC Lots-O-Post Thread

mini=man said:
I really feel like we should have a meet and greet sometime soon. Maybe when my buddy order's his lift I can have a few of you guys come up and give us a hand. $$$ is a possibillity.
Click to expand...

$$ isn't a concern...tell him to buy booze and food, that'll make me much happier :farmer: I'm pretty busy with a few of the upcoming weekends, but definitely be sure to post up when he'll be doing that and I'll make an effort to show up and lend a helping hand. Either that or I'll show up and :speepin:


:D
 
Re: THe NAC Lots-O-Post Thread

mini=man said:
I really feel like we should have a meet and greet sometime soon. Maybe when my buddy order's his lift I can have a few of you guys come up and give us a hand. CUSTOM TACOS is a possibillity.
Click to expand...

fify
 
You must log in or register to reply here.

Similar threads

R
Congratulations to our new Leadership!
Replies
2
Views
264
STROKER
STROKER
B
Looking for an passenger side OFFSET tie rod, 7/8-18 left hand thread offset to front of vehicle,
Replies
13
Views
371
Evan03
E
SAMSET
Check out the MWC Store on Breasy Things
Replies
2
Views
249
lesslimited
lesslimited
Bent
The BEST Medicine
Replies
7
Views
316
Nimrod
Nimrod
Jeepguy91
MWC election - Nominations for MWC Director at Large
Replies
3
Views
228
REWSTER
REWSTER
Back
Top