5spd_xj
<<the good ol days
- Location
- Dracut, MA
Re: THe NAC Lots-O-Post Thread
c'monnn, you're still viewin the thread, I seeeeee youuuuu
c'monnn, you're still viewin the thread, I seeeeee youuuuu
THe NAC Lots-O-BFG KO2 Thread
- Thread starter ROBZ95Xj
- Start date
5spd_xj
<<the good ol days
- Location
- Dracut, MA
Re: THe NAC Lots-O-Post Thread
that's always possible... what a loser! :laugh3:
that's always possible... what a loser! :laugh3:
5spd_xj
<<the good ol days
- Location
- Dracut, MA
Re: THe NAC Lots-O-Post Thread
hmm, maybe if i make it seem not so pointless to post, he will...
what's the widest you can do for a wheel spacer on a *rear* axle, do you think? I've been thinking I'd like to just keep it all wider, cause i love stability... comments? I posted in my build thread, but we'll see what the talkative crew has to say
hmm, maybe if i make it seem not so pointless to post, he will...
what's the widest you can do for a wheel spacer on a *rear* axle, do you think? I've been thinking I'd like to just keep it all wider, cause i love stability... comments? I posted in my build thread, but we'll see what the talkative crew has to say
5spd_xj
<<the good ol days
- Location
- Dracut, MA
Re: THe NAC Lots-O-Post Thread
noo, colin leftttt. hahah
noo, colin leftttt. hahah
Hackmeister
NAXJA Forum User
- Location
- Pittsburgh
Re: THe NAC Lots-O-Post Thread
psh who works at their job
psh who works at their job
5spd_xj
<<the good ol days
- Location
- Dracut, MA
Re: THe NAC Lots-O-Post Thread
question still stands tho, you two.
question still stands tho, you two.
asp
NAXJA Forum User
- Location
- Westport, MA
Re: THe NAC Lots-O-Post Thread
2" probably. hard to say. you'll be pwning bearings i bet, though
2" probably. hard to say. you'll be pwning bearings i bet, though
5spd_xj
<<the good ol days
- Location
- Dracut, MA
Re: THe NAC Lots-O-Post Thread
yeah, not so bad on the rear though, i would think?
yeah, not so bad on the rear though, i would think?
5spd_xj
<<the good ol days
- Location
- Dracut, MA
Re: THe NAC Lots-O-Post Thread
Bill says time for a rear axle hunt. I don't like that idea. lol
Bill says time for a rear axle hunt. I don't like that idea. lol
asp
NAXJA Forum User
- Location
- Westport, MA
5spd_xj
<<the good ol days
- Location
- Dracut, MA
Re: THe NAC Lots-O-Post Thread
I mean, I *do*, obviously. but $ wise... no no no. not now. I'm currently researching options as far as narrowing the front goes... I would do waggy width, but then the driver side tube is pretty short, and the brackets would end up interfering with the center chunk's casting. If I did a waggy width passenger side and stock ford driver's, its only actually getting shortened by a little under 2". Which would put the front axle at about 65" WMS and the rear a bit under 61"... which is why I was considering the 2" spacers, would make sense, right?
I mean, I *do*, obviously. but $ wise... no no no. not now. I'm currently researching options as far as narrowing the front goes... I would do waggy width, but then the driver side tube is pretty short, and the brackets would end up interfering with the center chunk's casting. If I did a waggy width passenger side and stock ford driver's, its only actually getting shortened by a little under 2". Which would put the front axle at about 65" WMS and the rear a bit under 61"... which is why I was considering the 2" spacers, would make sense, right?
Hackmeister
NAXJA Forum User
- Location
- Pittsburgh
Re: THe NAC Lots-O-Post Thread
yeah x2 on the bearings. try to look up the spec sheets from timken?
yeah x2 on the bearings. try to look up the spec sheets from timken?
5spd_xj
<<the good ol days
- Location
- Dracut, MA
Re: THe NAC Lots-O-Post Thread
what spec sheets might you speak of?
what spec sheets might you speak of?
5spd_xj
<<the good ol days
- Location
- Dracut, MA
Re: THe NAC Lots-O-Post Thread
Hmm... if I used a EB passenger with f150 driver, I'd be at a good WMS but the pinion would be pretty offset.
Hmm... if I used a EB passenger with f150 driver, I'd be at a good WMS but the pinion would be pretty offset.
5spd_xj
<<the good ol days
- Location
- Dracut, MA
Re: THe NAC Lots-O-Post Thread
who wants to crunch numbazzzzz with meee? lol. Anthony... we're gonna be doing this alot Sunday, fair warning. hahah
who wants to crunch numbazzzzz with meee? lol. Anthony... we're gonna be doing this alot Sunday, fair warning. hahah
asp
NAXJA Forum User
- Location
- Westport, MA
Re: THe NAC Lots-O-Post Thread
eff laundry
eff laundry
5spd_xj
<<the good ol days
- Location
- Dracut, MA
Re: THe NAC Lots-O-Post Thread
yeah. eff laundry is right. get your engineerin thinkin cap on dood! lol
yeah. eff laundry is right. get your engineerin thinkin cap on dood! lol
asp
NAXJA Forum User
- Location
- Westport, MA
Re: THe NAC Lots-O-Post Thread
it's not that hard... as long as you have it all laid out efficiently
it's not that hard... as long as you have it all laid out efficiently
5spd_xj
<<the good ol days
- Location
- Dracut, MA
Re: THe NAC Lots-O-Post Thread
Yeah. well, I ought to have the axle bare before Sunday, so if you want we can look at some possibilities then...
Yeah. well, I ought to have the axle bare before Sunday, so if you want we can look at some possibilities then...
asp
NAXJA Forum User
- Location
- Westport, MA
Re: THe NAC Lots-O-Post Thread
yeah. inner C's off too?
yeah. inner C's off too?
Similar threads
