THe NAC Lots-O-BFG KO2 Thread

[5spd_xj]

Re: THe NAC Lots-O-Post Thread

YAWNNNNN

 

[XBoBJ]

Re: THe NAC Lots-O-Post Thread

Tuesday.......

 

[themangeraaad]

Re: THe NAC Lots-O-Post Thread

yeah... about that...

 

[mini=man]

Re: THe NAC Lots-O-Post Thread

wtf did you do?

I just grabbed a pile of the 2.5" exhaust pipe in my garage and cut and welded shit until it fit. But now it at least has a muffler that has chambers and not straight through, and it comes out where it's supposed to so I'm sure that's helping my back pressure issue that I had. I might end up tossing a resonator in there for the hell of it, but probably not...

 

[ROBZ95Xj]

Re: THe NAC Lots-O-Post Thread

I just grabbed a pile of the 2.5" exhaust pipe in my garage and cut and welded shit until it fit. But now it at least has a muffler that has chambers and not straight through, and it comes out where it's supposed to so I'm sure that's helping my back pressure issue that I had. I might end up tossing a resonator in there for the hell of it, but probably not...

cats thend to help alot with chambered mufflers on the 4.0's

 

[mini=man]

Re: THe NAC Lots-O-Post Thread

I'm broke and this was $free.99

 

[Dundy]

Re: THe NAC Lots-O-Post Thread

Mark- Peed sitting down **DISQUALIFIED**

 

[RCman]

Re: THe NAC Lots-O-Post Thread

AWSOME!

http://www.artistdirect.com/video/five-finger-death-punch-under-and-over-it/113437

Didn't watch the video, but yeah, good song. Hasn't the single been out of awhile now?

My buddy cooks wings at the local bar...he's been trying for a few weeks now to perfect his 'insanity' hot wing sauce.

Last few tries it's been good, but not brutal...the most recent one just left me sitting in the corner, literally crying, sucking on bread. Then i made the mistake of wiping my eye.

XXXX this.

Blair's death sauce, fresh habaneros, fresh ghost chiles, and some frank's.

Yes please.

YAWNNNNN

X2.

 

[rweaver138]

Re: THe NAC Lots-O-Post Thread

I'm broke and this was $free.99

i need to fix my manifold and put a muffler on mine, it sounds like a tractor and its starting to get annoying

 

[ktm racer 419]

Re: THe NAC Lots-O-Post Thread

this axle is a cucv with 4.56's srw. ima buy it tonight if hes around for me to pick it up

 

[themangeraaad]

Re: THe NAC Lots-O-Post Thread

While sitting at work in the morning I think of things like: Who the fawk decided to grind up these little [coffee] beans and filter hot water through them to make this delicious drink I'm enjoying right now?

I feel like I have already heard the answer to that question at some point but I can't think of the answer right now and don't feel like googling.

 

[ROBZ95Xj]

Re: THe NAC Lots-O-Post Thread

Didn't watch the video, but yeah, good song. Hasn't the single been out of awhile now?

Yes please.

X2.

Single has been out for a month and full album will be out next month. Can't wait!

And x3

 

[vetteboy]

Re: THe NAC Lots-O-Post Thread

Some of you saw the in-progress photo of this, but my buddy set up this 9/11 tribute at his shop:

(those are both ZJ's)

 

[asp]

Re: THe NAC Lots-O-Post Thread

Dropping one now in the super secret bathroom I discovered at the the end of my building

Are you 'reading a magazine' in the super secret bathroom on the 8th floor?

 

[MoparManiac]

Re: THe NAC Lots-O-Post Thread

So I think this is what I'm going to do about my driveshaft. All parts from driveshaft superstore.

Long slip spline. 16 spline 1.5" diameter (7" working travel, 9.25" long)

Long matching slip yoke for 1350 joint- TOP, bottom is 1310 (in preparation for 440 power)

And get the correct matching flange yoke for the 1350 and my D60. To upgrade all that should cost about $200 shipped.

 

[XJLI]

Some of you saw the in-progress photo of this, but my buddy set up this 9/11 tribute at his shop:

(those are both ZJ's)

That's sick

 

[billyjp2]

Re: THe NAC Lots-O-Post Thread

colin, are you going to be done for the 24th?

 

[MoparManiac]

Re: THe NAC Lots-O-Post Thread

colin, are you going to be done for the 24th?

Hopefully.

Going to order the driveshaft parts tomorrow (gotta measure my bolt circle on the rear axle flange) and finish it up one night next week.

Also going to pull the fuel cell this weekend and get it welded up one night next week rather than deal with the hassle of shipping it back and forth and redoing my fuel pump setup.

 

[Dundy]

Re: THe NAC Lots-O-Post Thread

Also going to pull the fuel cell this weekend and get it welded up one night next week rather than deal with the hassle of shipping it back and forth and redoing my fuel pump setup.

I would contact them and take pictures of the leak. If they want you to send it back then don't worry about it but they might just send you a new cell from the pictures.

 

[billyjp2]

Re: THe NAC Lots-O-Post Thread

lets go wheelin