ktm racer 419
NAXJA Forum User
- Location
- ROW DIALIN
Re: THe NAC Lots-O-Post Thread
and i got the most badass fuel cell with it.
i am happy
and i got the most badass fuel cell with it.
i am happy
THe NAC Lots-O-BFG KO2 Thread
- Thread starter ROBZ95Xj
- Start date
- Location
- Rainy side of Washington
Re: THe NAC Lots-O-Post Thread
You are a lucky asshole :thumbup:
Hope the snow stays away, another day or two of this and I will be able to get back to work!
You are a lucky asshole :thumbup:
Hope the snow stays away, another day or two of this and I will be able to get back to work!
Re: THe NAC Lots-O-Post Thread
Finally got some rear light options figured out. According to the dimensions they should just fit. $21 and free shipping can't hurt to try since there was nothing like this available locally. Hopefully they are bright enough.
https://www.gpartsinc.com/p-198-set-of-2-red-led-15-series-marker-lights-black-base-hotwires.aspx
Finally got some rear light options figured out. According to the dimensions they should just fit. $21 and free shipping can't hurt to try since there was nothing like this available locally. Hopefully they are bright enough.
https://www.gpartsinc.com/p-198-set-of-2-red-led-15-series-marker-lights-black-base-hotwires.aspx
Last edited:
billyjp2
NAXJA Forum User
- Location
- Indian Orchard MA
Re: THe NAC Lots-O-Post Thread
Hey Ken, did your brother get a video of your hillclimb yesterday?
Hey Ken, did your brother get a video of your hillclimb yesterday?
- Location
- Rainy side of Washington
Re: THe NAC Lots-O-Post Thread
Dunno, not sure. I'll ask him...
I'm really hoping someone got a rotm worthy shot. If not, I'll have to try again next week :gee:
Dunno, not sure. I'll ask him...
I'm really hoping someone got a rotm worthy shot. If not, I'll have to try again next week :gee:
Begster
NAXJA Forum User
- Location
- Cape Cod/Boston, Mass
Re: THe NAC Lots-O-Post Thread
Bill, there is a steel rim sitting in the back of Carmelo's comanche right now to be delivered to Colin.
Bill, there is a steel rim sitting in the back of Carmelo's comanche right now to be delivered to Colin.
foxwar71
NAXJA Forum User
- Location
- Foxboro, MA
- Location
- Rainy side of Washington
Re: THe NAC Lots-O-Post Thread
Should be able to plug it back in and go. I'm not sure I remembered to fully tighten the screws holding the drivers to the case though, so it would be a good idea to pull it out and tighten the 4 screws on the side. No need for high torque just tweak em a little.
It may still drain the battery though. Couldn't figure that out, might be a bad ground like anthony said.
Should be able to plug it back in and go. I'm not sure I remembered to fully tighten the screws holding the drivers to the case though, so it would be a good idea to pull it out and tighten the 4 screws on the side. No need for high torque just tweak em a little.
It may still drain the battery though. Couldn't figure that out, might be a bad ground like anthony said.
MoparManiac
NAXJA Forum User
- Location
- Amherst, NH
Re: THe NAC Lots-O-Post Thread
My father is getting a lathe for free. Picking it up on Tuesday.
Weighs a couple hundred pounds but no idea what model it is or anything.
I'm gonna have to learn how to make stuff now.
arty:
My father is getting a lathe for free. Picking it up on Tuesday.
Weighs a couple hundred pounds but no idea what model it is or anything.
I'm gonna have to learn how to make stuff now.
arty:
cmelo
NAXJA Forum User
- Location
- Stoughton,MA
Re: THe NAC Lots-O-Post Thread
I'm making all of my driveshafts at your house.
My father is getting a lathe for free. Picking it up on Tuesday.
Weighs a couple hundred pounds but no idea what model it is or anything.
I'm gonna have to learn how to make stuff now.
I'm making all of my driveshafts at your house.
Re: THe NAC Lots-O-Post Thread
i just need radio for long trips, i can unplug it after
Re: THe NAC Lots-O-Post Thread
bitchin, hope its a ww2 era belt driven, we had them in machine shop and i always picked em overe the gear heads and fancier ones, the were simple to work with and quiet
My father is getting a lathe for free. Picking it up on Tuesday.
Weighs a couple hundred pounds but no idea what model it is or anything.
I'm gonna have to learn how to make stuff now.
bitchin, hope its a ww2 era belt driven, we had them in machine shop and i always picked em overe the gear heads and fancier ones, the were simple to work with and quiet
5spd_xj
<<the good ol days
- Location
- Dracut, MA
Re: THe NAC Lots-O-Post Thread
Yuuuuup!
Yuuuuup!
foxwar71
NAXJA Forum User
- Location
- Foxboro, MA
Re: THe NAC Lots-O-Post Thread
If its a legit lathe, expect that to be more then a couple hundred pounds. My bridgeport has no extra fancy options and is still around like 1900 pounds. Be careful when moving machinery, you gotta be VERY careful with it. If you want some help/tips in rigging, I'll give you a hand. I also have access to proper rigging stuff to move junk. I'll pick it up with the crane and put it out on your back deck to use at your convenience
My father is getting a lathe for free. Picking it up on Tuesday.
Weighs a couple hundred pounds but no idea what model it is or anything.
I'm gonna have to learn how to make stuff now.
If its a legit lathe, expect that to be more then a couple hundred pounds. My bridgeport has no extra fancy options and is still around like 1900 pounds. Be careful when moving machinery, you gotta be VERY careful with it. If you want some help/tips in rigging, I'll give you a hand. I also have access to proper rigging stuff to move junk. I'll pick it up with the crane and put it out on your back deck to use at your convenience
MoparManiac
NAXJA Forum User
- Location
- Amherst, NH
Re: THe NAC Lots-O-Post Thread
I'm willing to bet its a mini lathe or something.
I'm willing to bet its a mini lathe or something.
foxwar71
NAXJA Forum User
- Location
- Foxboro, MA
Re: THe NAC Lots-O-Post Thread
Okay, that should be alot easier to manage then.
Okay, that should be alot easier to manage then.
Similar threads
