THe NAC Lots-O-BFG KO2 Thread

[kastein]

Re: THe NAC Lots-O-Post Thread

OHC wooooorks

except for the temp sensor, because I'm too lazy to pull the header panel off and bolt it down where it's supposed to go + run the cable for it.

 

[JrTxJ]

Re: THe NAC Lots-O-Post Thread

OHC wooooorks

except for the temp sensor, because I'm too lazy to pull the header panel off and bolt it down where it's supposed to go + run the cable for it.

iirc, when I did mine, the wiring was already there...just needed the sensor plugged in and it was located on the back side of the bumper by the radiator.

 

[kastein]

Re: THe NAC Lots-O-Post Thread

Yeah, I've pulled em out a few times... I am just too lazy to put it in. I've got the harness and sensor sitting on my desk but can't find the motivation to care really, the "OC" display looks like 0C which is gonna be fairly accurate for a month or two :dunce:

 

[Dundy]

Re: THe NAC Lots-O-Post Thread

it's there on mine too. It could be just the 97+ xj's.

 

[asp]

Re: THe NAC Lots-O-Post Thread

still got mine...

x2

 

[foxwar71]

Re: THe NAC Lots-O-Post Thread

my dad thinks its gunna be too hard to cut the 5/16" truss with cutoff wheels........































........so were gunna go to airgas and look at plasma cutters and pick one out

 

[themangeraaad]

Re: THe NAC Lots-O-Post Thread

my dad thinks its gunna be too hard to cut the 5/16" truss with cutoff wheels........

........so were gunna go to airgas and look at plasma cutters and pick one out

Lucky SOB...

I may be renting a 50'x50' garage soon... so if I do get that y'all are welcome to swing by on nights/wkends while I am there (indoor place to work during the winter). Not sure if there is electricity but I assume there must be... a 50x50's gotta have lights... if not I have a generator available... and you can use it as long as you show up with plasma cutters and tube benders to make my life cheaper/easier

 

[redneckboarder]

Re: THe NAC Lots-O-Post Thread

plasma cutters are 10000x times better than cut off wheels

 

[ROBZ95Xj]

Re: THe NAC Lots-O-Post Thread

I am quite interested. Will keep an eye out for future posts.

the long arms will be availible within the next couple weeks, hes ordering his Clayton arms tomorow

 

[billyjp2]

Re: THe NAC Lots-O-Post Thread

going to get my new rear axle tomorrow, and its only a few minutes away from Travis

 

[ROBZ95Xj]

Re: THe NAC Lots-O-Post Thread

going to get my new rear axle tomorrow, and its only a few minutes away from Travis

what are you gonna run now?

 

[billyjp2]

Re: THe NAC Lots-O-Post Thread

35 spline dana 60.

 

[ROBZ95Xj]

Re: THe NAC Lots-O-Post Thread

HAWTNESS!

 

[foxwar71]

Re: THe NAC Lots-O-Post Thread

rear 60s suck

 

[billyjp2]

Re: THe NAC Lots-O-Post Thread

did i say 60? I meant portal axle

 

[sheepjeep]

Re: THe NAC Lots-O-Post Thread

 

[foxwar71]

Re: THe NAC Lots-O-Post Thread

did i say 60? I meant portal axle

:thumbup: thats more like it

 

[scully]

Re: THe NAC Lots-O-Post Thread

nice vid.
btw i was just informed by my wife(nicely)that packing for our move tomorrow morning is probably more important than ::.
she was like :nono:
and i was like :dunno:
and then i went :compwork:
and then she went :lecture:
and then i was like :doh: its 10:30 and still have three hours+of packing!!!

 

[billyjp2]

Re: THe NAC Lots-O-Post Thread

awsome use of smilies

 

[asp]

Re: THe NAC Lots-O-Post Thread

x2. good use of smilies.