- Location
- Columbus, In
Go figure that Ken knows about Trannies!
Flexd' hopefully not the kind with adam's apples' XJ
Flexd' hopefully not the kind with adam's apples' XJ
Important
- Thread starter bshaw
- Start date
- Location
- Rainy side of Washington
I hauled so many man trannies around in that stabbin wagon I brought to WF12... then I ended up blowing the tranny in it and scrapped it. Didn't work quite right after that.
- Location
- Painted Hills, Indiana
That could really read bad.
shortxjdoug
NAXJA Forum User
- Location
- Chattanooga tn
hey flex! what kind of mpg did your junk get to and from moab?
- Location
- Michigan
Well, the fluid quality is/was bad. I have changed the filter once, and changed the fluid again last night (what I could from the pan). I kick myself in the ass for not buying a new torque converter when the motor was out.
*89Laredo*
NAXJA Forum User
- Location
- Sheffield, IA
Burns good though
- Location
- Rainy side of Washington
Oh, I'm fully aware :anon:
- Location
- Warsaw, IN
Is it gonna make the trip tomorrow? Is it acting better since you changed the fluid?
- Location
- Michigan
Re: Re: Important
I didn't hear from you, so I assumed it didn't kill your truck.
I went to bed at 4am.
Fore 'Flos nasty red fluid got drank by Dylan's nasty old diesel' Wheeler
Burns good though
I didn't hear from you, so I assumed it didn't kill your truck.
I went to bed at 4am.
Fore 'Flos nasty red fluid got drank by Dylan's nasty old diesel' Wheeler
- Location
- Southwest IN
Enroute to get snow tires on the company car. 6" on the ground and still coming down.
BRIANHO13
<- Yum Chocolate
- Location
- Spring, TX
Enroute to get snow tires on the company car. 6" on the ground and still coming down.
I feel kinda bad telling people they have to work tomorrow.....lights are on unless its a state of emergency.
BRIANHO13
<- Yum Chocolate
- Location
- Spring, TX
Of course I get over it pretty quick.
- Location
- Columbus, In
Somewhere around 16-16.5 average.
terrehautian
NAXJA Forum User
- Location
- Terre Haute
Came across a Chevy Equinox stuck in a ditch earlier. Was going to help them but they didn't have any recovery points and the owner couldn't see anywhere to attach a strap.
OutkastBoss
NAXJA Forum User
- Location
- Saint louis
I pretty much followed a write up I found on some site called jeep kings, I think the thread was called extrem xj rocker replacement.
And yes it is spelled extrem without the e ..
anyway I did a run down of mine in my build thread
http://www.naxja.org/forum/showthread.php?t=1080904&page=6
Scroll down to post 84-86
http://www.naxja.org/forum/showthread.php?t=1080904&page=7
And post 102 for the tube steps
BRIANHO13
<- Yum Chocolate
- Location
- Spring, TX
I love being able to drive around when everyone else is staying off the road
- Location
- Columbus, In
Me too.....but I'm just gonna sit on the couch, eat a sammich and watch Archer.
POLAR_JEEP_04
NAXJA Forum User
- Location
- Ohio
Me too. I drove home with the truck in 2wd with an empty bed.
BRIANHO13
<- Yum Chocolate
- Location
- Spring, TX
Came home, picked up Lynn and Ted and went to target and went out to eat. Pretty much had the places to ourselves. It was nice.
poorboy87
NAXJA Forum User
- Location
- Linton Indiana
So far we have about 8 inches ish up here. This morning on the way to work there was about 4 inches on the ground.
I put 2x6 box in on mine. Cut the rockers out at the bottoms last bend in the door jam area then flush with the pinch weld. Set the box tube in and angled it down a little bit. Then welded 1 inch angle iron on the box tube and to the factory pinch weld. So far so good.
Now I really need to finish the floor on the drivers side.
I put 2x6 box in on mine. Cut the rockers out at the bottoms last bend in the door jam area then flush with the pinch weld. Set the box tube in and angled it down a little bit. Then welded 1 inch angle iron on the box tube and to the factory pinch weld. So far so good.
Now I really need to finish the floor on the drivers side.
