Clutch, Pressure Plate and Flywheel

[David_Bricker]

I have a clutch, pressure plate and flywheel for a '95 XJ 4.0L engine. It was installed for less than 1000 miles. The clutch and pressure plate surfaces are in excellent shape. The flywheel has a couple of small heat spots, but they may easily come out with a bit of sanding. They are not deep.

The flywheel was balanced when the clutch was installed. It ran very smoothly, and there was no clutch chatter whatsoever.

I believe I also have the throwout bearing, but I'd install a new one regardless.

Located near Pasadena, and I am asking $100.

David Bricker / SYR

 

[David_Bricker]

No one has a manual trans anymore? This could make a really good spare.

Price drop to $75.

David Bricker / SYR

 

[GrimmJeeper]

if someone local buys this and brings me the flywheel i'll resurface it for 25 bucks at my NAPA shop, it will be like brand new.

 

[David_Bricker]

You mean no one runs manual transmissions any more? This would make a great spare set, or replacement for your tired clutch.

David Bricker - SYR - PSR

 

[David_Bricker]

Surely someone has an AX-15, and they need a decent clutch and pressure plate for a really good price? And, don't call my Shirley.

David Bricker / SYR - EWR

 

[dukie564]

David what brand is it? You're local so I may pick it up for when mine shits the bed

 

[dukie564]

Oh wait...not pasadena md...I'm a tard. Stupid phone app

 

[David_Bricker]

No worries! I'm a bit all over the place, but the clutch is in Pasadena, CA. I'd be willing to ship it, but I'm guessing hipping won't be cheap.

David Bricker / SYR - EWR

 

[David_Bricker]

Will someone please buy this, and get it out of my (and my storage person's) hair. It really is a good deal, and it's in decent shape. Only reason I didn't reuse it was because I didn't know its condition before removal, and I needed parts on hand.

David Bricker / SYR

 

[5-90]

Question - did you happen to measure the lengths of the screws used to attach the flywheel to the crankshaft?

 

[David_Bricker]

Question - did you happen to measure the lengths of the screws used to attach the flywheel to the crankshaft?

Surprisingly enough, yes. I wanted to get new bolts, but couldn't find them in time.

1/2-20 Overall length 1.121". Thread length 0.863".

Now, please buy my clutch!

David Bricker / SYR

 

[5-90]

Surprisingly enough, yes. I wanted to get new bolts, but couldn't find them in time.

1/2-20 Overall length 1.121". Thread length 0.863".

Now, please buy my clutch!

David Bricker / SYR

Thank you - that thread length is what I wanted (5/8".)

I would, if I needed a clutch! GLWS.

 

[David_Bricker]

Thank you - that thread length is what I wanted (5/8".)

I would, if I needed a clutch! GLWS.

If you need to know how long the flywheel bolts are, you need a clutch!

David Bricker / SYR

 

[David_Bricker]

Thank you - that thread length is what I wanted (5/8".)

I would, if I needed a clutch! GLWS.

Got to thinking about this - thread length is more like 7/8". Was that just a typo on your part?

David Bricker / SYR

 

[scottmcneal]

BUMP

 

[5-90]

If you need to know how long the flywheel bolts are, you need a clutch!

David Bricker / SYR

Not so much - I just keep forgetting to measure them, so I can add the information to my site, or find alternatives to OEM (just as the flexplate screws. Yeah, you can get OEM, but I found a better kit through ARP that's intended for Pontiac V8 engines...)

 

[5-90]

Got to thinking about this - thread length is more like 7/8". Was that just a typo on your part?

David Bricker / SYR

Apparently, it was. Thanks!