- Location
- Middle Tennessee
Great solution to the hard-to-find MJ tail lights. Very clever.
-
Welcome to the new NAXJA Forum! If your password does not work, please use "Forgot your password?" link on the log-in page. Please feel free to reach out to [email protected] if we can provide any assistance.
2014 MJ (code name Abby)
- Thread starter KPTHEMP
- Start date
- Location
- Hartsville, South Carolina
Agreed. I hope I get to see this thing in person when its all done.
- Location
- Harrisburg, NC
Hopefully he gets it done and brings it to the Crawl to wheel!
Mr.Shrek
NAXJA Forum User
- Location
- Murfreesboro, TN
Looking good KP as I would expect from all of your builds.
highspeed
NAXJA Forum User
- Location
- Owens Cross Roads, Alabama
Awesome. I check in everyday to see the progress
- Location
- Columbus, In
Kris, I can't wait to see this thing in person!
Picked up a few things a PAP
-ignition and door lock/key set (donor door locks were trashed)
-HMSL/Cargo light from late model dakota
-Front axle breather hose
-door insulation pads
-Hood release cable to rod mechanism (donor was rusted)
Installed hood latching hardware
Installed HMSL/ cargo light (wiring pending)
Installed door trim/handles/locks
Installed wiper cowl
Glass is getting set tomorrow...
-ignition and door lock/key set (donor door locks were trashed)
-HMSL/Cargo light from late model dakota
-Front axle breather hose
-door insulation pads
-Hood release cable to rod mechanism (donor was rusted)
Installed hood latching hardware
Installed HMSL/ cargo light (wiring pending)
Installed door trim/handles/locks
Installed wiper cowl
Glass is getting set tomorrow...
Got a lot done today...
-wired the HMSL/cargo light (made a jumper using the XJ tailgate harness and the tail of the donor HMSL, very clean. I wired the Cargo lights to the defroster button, also in the same harness, which illuminates on the dash as well as time delay, auto off)
-Final install of the windshield from the donor XJ, which also happens to be an original Chrysler glass
-Reinstalled the Rear slider
-Installed the rear speakers and wiring from the donor XJ, tested the factory radio
-cut and Installed the donor XJ carpet
-Painted and started to install the rear cab cargo trim (paint match to factory agate)
-wired the HMSL/cargo light (made a jumper using the XJ tailgate harness and the tail of the donor HMSL, very clean. I wired the Cargo lights to the defroster button, also in the same harness, which illuminates on the dash as well as time delay, auto off)
-Final install of the windshield from the donor XJ, which also happens to be an original Chrysler glass
-Reinstalled the Rear slider
-Installed the rear speakers and wiring from the donor XJ, tested the factory radio
-cut and Installed the donor XJ carpet
-Painted and started to install the rear cab cargo trim (paint match to factory agate)
-Modified the seats with hinges from the 2-door PAP run, they now flip forward
-Refinished the Headliner board with fiberglass repair and with new material and installed
-Wired the lights for the "b" pillars into the overhead XJ lights/RKE Harness
and started to install the misc dash trim
-Refinished the Headliner board with fiberglass repair and with new material and installed
-Wired the lights for the "b" pillars into the overhead XJ lights/RKE Harness
and started to install the misc dash trim
highspeed
NAXJA Forum User
- Location
- Owens Cross Roads, Alabama
Love it..... Seats look comfy
Love the A$$ shot too.
Love the A$$ shot too.
- Location
- Harrisburg, NC
Love it!
IllianaXJ
NAXJA Forum User
- Location
- Southwest IN
That is a seriously nice truck. Can't wait to see it at the Crawl.
Lowrange2
NAXJA Forum User
- Location
- Abbeville, SC
I want it back now...
shortxjdoug
NAXJA Forum User
- Location
- Chattanooga tn
