WTT my parts for your XJ Control Arms Drop Brackets

[Moo Moo Jeep]

I want to trade my parts (anything from list below) for your Cherokee XJ Control Arms Drop Brackets. Depending on the value of the parts I can add some cash (not too much) or the other person can I'm interested in brackets made by Rough Country or Rubicon Express or any other company that makes them.

My parts:

New and Used XJ Parts: http://www.naxja.org/forum/showthread.php?t=1125116

31" Firestone M/T, stock tires and stock steel wheels: http://www.naxja.org/forum/showthread.php?t=1123273


Parting Dana 30 with locker: http://www.naxja.org/forum/showthread.php?t=1125326

XJ D44 axleshafts: http://www.naxja.org/forum/showthread.php?t=1125047

Bestop 2-Piece Soft Doors for YJ and CJ-7/CJ-8: http://www.naxja.org/forum/showthread.php?t=1124888

Dana 60 Detroit Locker: http://www.naxja.org/forum/showthread.php?t=1121840

Spidertrax 1.25" Wheel Adapters NIB: http://www.naxja.org/forum/showthread.php?p=246291288#post246291288

4 alloy wheels + 1 steel one: http://www.naxja.org/forum/showthread.php?p=246291289#post246291289

Rubicon Express ZJ 3.5" Coil Springs - Front & Rear: http://www.naxja.org/forum/showthread.php?t=1123919

 

[Moo Moo Jeep]

Nobody has Control Arms Drop Brackets for sale or trade?

 

[dan1977p]

I may be able to get my hands on some re drop brackets off an 89 for the d30 locker.

 

[Moo Moo Jeep]

Sounds good. Let me know. Brackets and braces or brackets only?

 

[dan1977p]

I'll check this afternoon and pull everything I can. Ill post pics so you can see what I have once I have them in hand.

 

[dan1977p]

Here is a photo of all the stuff. Not sure how shipping is going to go, though. When I offered up, I thought it was just the small 9x9x3.5 bit that goes in the existing pocket where the lower arm went. The part I didn't realize was the 22" long brace that ties into the crossmember holes. Those will make shipping flat rate impossible and I suspect shipping will be cost prohibitive. When it was cheap shipping, I was ok getting a locker of unknown health to try it out but I'm not sure I'm comfortable at this point.

 

[Moo Moo Jeep]

Here is a photo of all the stuff. Not sure how shipping is going to go, though. When I offered up, I thought it was just the small 9x9x3.5 bit that goes in the existing pocket where the lower arm went. The part I didn't realize was the 22" long brace that ties into the crossmember holes. Those will make shipping flat rate impossible and I suspect shipping will be cost prohibitive. When it was cheap shipping, I was ok getting a locker of unknown health to try it out but I'm not sure I'm comfortable at this point.

No problem. When I was checking Rubicon's brackets on-line I realized they are for lifts 5.5" and higher and my XJ has only 4-4.5" so they won't work for me anyway. Thank you for your time though. I have to go with Rough Country's brackets because they are for 4.5" lift.

 

[dan1977p]

Sorry about that. As with everything on these jeeps, nothing is as it seems and it's always harder than it should be.

I will say this, the jeep these came from only had probably 3.5" and was rolling 31's. From what I've read, they move the axle forward an inch and are 4.5" down so they position the control arms in the exact same spot as the RC ones.