What did you do to your XJ today

[RedJeep2.0]

block is ready to come out.... unbolt the trans and she out.

 

[nightfoam]

Finished up my "Mr Thirsty" mod

 

[GlueNTape]

You need to tack on some beer holders to be complete.

 

[XJCasper]

Finished up my "Mr Thirsty" mod

I need one of those

 

[kndrewa]

I need one of those

x2 where'd you get it?

 

[jeremybigs]

got the aluminum welded

and added the vent

now its done and painted.

the plate will have to come back off and will be bolted to the rear most tcase when i go to put it in the jeep but other then that its complete. i already had the rear driveline shortened so now i just need the front lenghtened. and figure out a linkage but ill worry about that later

 

[nightfoam]

x2 where'd you get it?

Pulled it off an old barn getting torn down last time I was in Pendleton...

 

[BenDiesel]

That's a sweet doubler ya got there. Mind if I come by some time to check it out? What case you putin behind it?

 

[jeremybigs]

thanks im going to put another 231 behind it for now see how it holds up if things dont work out ill find a d300 probly

 

[ECKSJAY]

What case you putin behind it?

Sees what you did there...

 

[TORX]

I haven't had any motivation to work on my junk for the past month. Luckily it's still holding together.

I did however go to the Pick-n-pull yesterday and snagged some parts for the DD. Today I replaced both front seat belts. The driver side spring was broke, and the passenger side was used as a chew toy for a dog, so I swapped in a fresh set.

Then I took down the fancy rear view mirror with lights, and replaced it with a plain jane stocker. The wiring for the lights was actually comical. Pink and purple 22gauge wire, and the ground wire (purple) was wrapped around the sun visor screw. Needless to say the lights didn't work.

At that point I started to get burned out so I called it a day.

 

[Muddy Beast]

Replaced my axle seals today...took a little longer than I would have liked, but luckily I talked the rents into letting me use the garage and parking my moms weekend toy in the driveway temporarily.

 

[Bronzewyrm]

there no MT/R's... should do me fine:thumbup:

 

[BoringDave]

got the aluminum welded

and added the vent

now its done and painted.

the plate will have to come back off and will be bolted to the rear most tcase when i go to put it in the jeep but other then that its complete. i already had the rear driveline shortened so now i just need the front lenghtened. and figure out a linkage but ill worry about that later

Where did you get the plans for this setup?

Dave

 

[Mountaincajun]

Mounted my tools on the top rack of the jeep. Bracket came off a Hummer(military issue).

 

[jonesinxj]

took advantage of JCR's Sale and ordered a transfer case skid

 

[jeremybigs]

Where did you get the plans for this setup?

Dave

there isnt a plan my buddy measured it up and did it. hes an engineer its what he does but he got the idea from the madrooster set up he just made his own and a few extras i mean you can see its just a flap plate with holes drilled in the right places and a shaft custom made but it is all lined up to the exact. in my old sami we made kindof the same thing with some sami tcases but instead of the custom shaft we just welded together two shafts it worked for it becuse it didnt go one the street.

 

[Gold Cobra]

Since waxjskier wouldn't help me, I had to hire the closest look-a-like in bigpimpinben. He help me bleed my brakes again. Hopefully its better, I won't know yet, I'm too drunk to drive it.

 

[RedJeep2.0]

Tryed pulling just the motor... No luck. Scott and I will try a few more things tomorrow. Then I guess the tranny will fallow?

 

[NW-ZJ-SCOTT]

Tryed pulling just the motor... No luck.

:gonnablow