solomon7
NAXJA Forum User
- Location
- Portland OR
Changed my oil and leaky OFA seals. Replaced valve Cover too. Everything was squeaky clean inside!
What did you do to your XJ today
- Thread starter Cherokeefever
- Start date
daveenlola
NAXJA Forum User
- Location
- Renton Wa
Learned about the crankshaft position sensor
Hope I can return the coil i bought
Hope I can return the coil i bought
dellstopjeep
NAXJA Forum User
- Location
- KUNA, ID
isnt it a good feeling when the ofa doesnt leak? :guitar:greensmok
YoureASissy
NAXJA Forum User
- Location
- Beaverton, OR
Bought lift shocks for my '01 XJ. Tomorrow morning I'll be putting my budget lift on with my boyfriend and NightFoam!
dellstopjeep
NAXJA Forum User
- Location
- KUNA, ID
Threesome???
BenDiesel
NAXJA Forum User
- Location
- lynnwood washington
i meet up with spikey puk to give him the spare engine i had for the 2.5 and found out he painted the poor girl black. guess hes not part of the white jeep club any more lol
then went up to the woods for some target practice
then went up to the woods for some target practice
mojojojo
NAXJA Forum User
- Location
- Gresham, Oregon
Usually my post run and pre run inspections are one in the same. but after noticing some more than normal noises i decided to remove all the wheels and crawl around underneith a bit today...
Found this on the drivers side
and this on the pass side
at least they match... :bawl:
Paging karl... can i have my back-up shim and pin back now
Found this on the drivers side
and this on the pass side
at least they match... :bawl:
Paging karl... can i have my back-up shim and pin back now
WaXJ_Skier
NAXJA Forum User
- Location
- Bellevue, Wa
Usually my post run and pre run inspections are one in the same. but after noticing some more than normal noises i decided to remove all the wheels and crawl around underneith a bit today...
Found this on the drivers side
and this on the pass side
at least they match... :bawl:
Paging karl... can i have my back-up shim and pin back now
that's what mine looked like after NWfest. is that the same spring plate from your dana 35?
WaXJ_Skier
NAXJA Forum User
- Location
- Bellevue, Wa
Got these in the mail
mojojojo
NAXJA Forum User
- Location
- Gresham, Oregon
Not sure ? I cant remember if i swapped plates with the axles or not ?
I do know that this is like the 4th set of center pins ive changed in the last 2 years. I thought i had it figured out the last time when i realized i was running the smaller 35 pins and the perch hole on the 44 takes the bigger pins.... but apparently that made NO improvement. FAWK !!! :gonnablow
Nicely done!Usually my post run and pre run inspections are one in the same. but after noticing some more than normal noises i decided to remove all the wheels and crawl around underneith a bit today...
Found this on the drivers side
and this on the pass side
at least they match... :bawl:
Paging karl... can i have my back-up shim and pin back now
First it was tie-rods, now it's center pins.
- Location
- Vancouver, WA
Killed it... She's dead.
Threw a main barring or two.
Motor swap before turkey day!!
Threw a main barring or two.
Motor swap before turkey day!!
WaXJ_Skier
NAXJA Forum User
- Location
- Bellevue, Wa
Make sure you torque everything down, any play with warp those very quickly. Also are you using s 3/8 or 5/16 pin? I think RE leaves use the larger 3/8 pin.
Bro-Quo
NAXJA Forum User
- Location
- Chicago, IL
8.8 pinion bearings are toast. Need to find a rear axle while i rebuild. fawk...
BenDiesel
NAXJA Forum User
- Location
- lynnwood washington
Hey just womderin were you guys get the pins from? I'm gona build a bastard pack gona need some
- Location
- Vancouver, WA
- Location
- Vancouver, WA
213,xxx
mojojojo
NAXJA Forum User
- Location
- Gresham, Oregon
Hey just womderin were you guys get the pins from? I'm gona build a bastard pack gona need some
Ive always got them from RE.... but maybe thats where i'm going wrong ?
Similar threads
