mojojojo
NAXJA Forum User
- Location
- Gresham, Oregon
did that this weekend on easter while it was raining. Today i just had my memories.... since i store it elsewhere, and couldnt stare at it today.
What did you do to your XJ today
- Thread starter Cherokeefever
- Start date
did that this weekend on easter while it was raining. Today i just had my memories.... since i store it elsewhere, and couldnt stare at it today.
hards91xj
NAXJA Member #790
- Location
- Tacoma Wa.
Using it for a DD this week and enjoying that smoooth , quiet , non-oil- leaking engine while trying to get stuff done to my DD Toyota pu.
2xtreme
NAXJA Forum User
- Location
- Kayak Pt, WA
I increased the castor on my front axle.
Installed a new front long shaft and then replaced the hub.
Michael
Installed a new front long shaft and then replaced the hub.
Michael
Metal Thrasher
NAXJA Forum User
- Location
- life
Didn't the Passenger side hub get replaced back in September?
2xtreme
NAXJA Forum User
- Location
- Kayak Pt, WA
I have swapped hubs a total of 8 times since September
I only do an oil change 1 time per year though.
Something seems to be a little off on my maintenance schedule :scottm:
Michael
PoSxJ
NAXJA Forum User
- Location
- Portland, Or
I installed new front extended brakes lines from RE, took about am hour. Then I spent 4 hours bleeding the brakes and trying to figure out why they still aren't working correctly. I bet its something simple that I'm over looking. But I'm running out of patience.
Are the calipers on the right way, with the bleeder on the top?
The jeep got new plugs, cap & rotor, and u-joints today. I really hope I found the mystery noise I've been trying to track down.
mojojojo
NAXJA Forum User
- Location
- Gresham, Oregon
Are the calipers on the right way, with the bleeder on the top?
The jeep got new plugs, cap & rotor, and u-joints today. I really hope I found the mystery noise I've been trying to track down.
hmmm.... is that the noise i told you was just the exhaust ?
- Location
- Vancouver, WA
Are the calipers on the right way, with the bleeder on the top?
The jeep got new plugs, cap & rotor, and u-joints today. I really hope I found the mystery noise I've been trying to track down.
I have an 18volt cordless electric grease for that!
Makes it more fun to grease stuff!!
hards91xj
NAXJA Member #790
- Location
- Tacoma Wa.
Looks good, needs a little grease and good as new. I carry a couple of old U-joints with me incase I need them or for that trail repair when someone needs a cap for their front driveline so they can finish out the day and get back to camp in the Little Naches area . It does happen but not "2xstreme" ly often...
Bronzewyrm
NAXJA Forum User
- Location
- Independence,or
you would be amazed at what dustin pulls out of his trail box :clap:
BenDiesel
NAXJA Forum User
- Location
- lynnwood washington
i put a full tank of gas in it.
XJ=Fun
NAXJA Forum User
- Location
- Klamath Falls
Lets see, today I bench bled the bitch, and fixed the broken seat bracket.Maybe I will put my long brake lines on tomorrow........then i have to start thinking about finally putting my crown sye in and front drivelines. FUN FUN FUN!!!
NickDanger_XJ
NAXJA Forum User
- Location
- Tumwater, WA
I got some new window decals that I ordered in the mail today, and I'll put them on as soon as I get my Jeep out of the shop..... does that count as anything?
PoSxJ
NAXJA Forum User
- Location
- Portland, Or
hards91xj
NAXJA Member #790
- Location
- Tacoma Wa.
Put in a different speedo gear :repair: now it`s 1 mph off at 40 mph .. yahoo thats alot better ..
NickDanger_XJ
NAXJA Forum User
- Location
- Tumwater, WA
I should probably do that someday. Got pulled over yesterday for doing 6 over, and I'm pretty sure my speedo was right at 25.
Then I got hassled for having no mudflaps as well.
Then I got hassled for having no mudflaps as well.
cob'sxj
NAXJA Forum User
- Location
- University Place, WA
Yesterday I installed some new coils in the front along with a new tracbar and a shackle in the rear. Also some new bilstein shocks for the front. The shocks made a world of difference for the front and the tracbar totally eliminated the bump steer and other horrible noises coming from the front end. Now Im trying to remove those studs from the tcase crossmember so that I can get the drop kit in there until I can afford an sye and new driveshaft. Then tommorow I will install my cool new shackle brackets so someone can pull me out of the crud. Assuming that this tcase drop ever gets in Im pretty sure Im gonna be done wrenching for a while
mojojojo
NAXJA Forum User
- Location
- Gresham, Oregon
not much today... went and picked up Josh's old doors, tried to get the windshield out also, but gave up after about an hour. Swapped out my old tires for some temporary rollers (thanks Nick) till my new ones show up. Took the old ones to the shop to have em unmounted. Sunday i will be trimming the bottoms off all four new doors to clear the rocker replacements, then ripping out the rest of the interior, front seats, and whats left of the carpet.
