Working on it. I absolutely hate the ignition system on the 00-01. Now that I'm swapped to an HO, I'm mid process on pulling out the PCM and engine harness and going to a distributor, PCM, coil, etc from a 98. I hope to have nothing left from the 00-01s except fpr the body by the time I'm done with this thing.
What did you do to your XJ today
- Thread starter Cherokeefever
- Start date
Mine doesn't change. It stays toght. I just suck at adjusting the wheel. I always end up screwing up by giving one side too much throw, etc. Lol
XJCasper
NAXJA Member #1042
- Location
- Yelm, Washington
Lets see..
Been a bad month:
Leaving some specific details out.
Some of this is paid for, other was just taken back and covered under warranty, just for the heck of it:
Replaced
TPS, IAC, wires, cap, rotor, CPS, distributor pick-up,
ignition coil (this had it running for a day) and finally a new PCM.
My son questioned bad gas, so he added injector cleaner and octane booster, just for sh!ts and giggles....
But it runs now. Just scared to leave town.
Been a bad month:
Leaving some specific details out.
Some of this is paid for, other was just taken back and covered under warranty, just for the heck of it:
Replaced
TPS, IAC, wires, cap, rotor, CPS, distributor pick-up,
ignition coil (this had it running for a day) and finally a new PCM.
My son questioned bad gas, so he added injector cleaner and octane booster, just for sh!ts and giggles....
But it runs now. Just scared to leave town.
muddypunk
TOOL
- Location
- Coupeville Whidbey Island washington
Did you buy a New new pcm or a bone yard unit I've traced my issues back to it just haven't had time to get to a wrecking yard.
XJCasper
NAXJA Member #1042
- Location
- Yelm, Washington
Picked up a new PCM. Had it running good for a day, then it started studdering to a stall. My son was messing around with it until it stalled out, and now he is telling me there is smoke. I asked him if it was smoke or steam? And he is not sure. I will be replacing spark plugs on Wed. Getting some severe missing before she stalled out. Heading back to check the wiring and grounds.
What did I do to my XJ today?
I stared at it. Waiting to meet up with Dustin to swap parts so I can get the bastard running after the motor and harness swap. I'm a sad panda ... this darn thing hasn't been running in months and there's all this awesome snow/mud to play in.
I stared at it. Waiting to meet up with Dustin to swap parts so I can get the bastard running after the motor and harness swap. I'm a sad panda ... this darn thing hasn't been running in months and there's all this awesome snow/mud to play in.
- Location
- Seattle, WA
Finally got my gauges working again after they shut off 3 weeks ago. Turned out it was a corroded plug in my overhead console going to the Sentry remote lock system. Took way to long to figure it out. Just need to solve the water leaks into the cabin now.
FordVader
NAXJA Forum User
- Location
- Bonney Lake
Replaced my transmission cooler lines with rubber over engine lines. Cost $50 including tranny fluid. Looks and works awesome. My old lines had been spliced and repaired way too many times causing overheating.
Demonoid369
NAXJA Forum User
- Location
- Salem, OR
Not really from today, but from Sunday.
Cline Butte OHV
I've wanted to go there so bad. I've seen some good wheeling pics from there
Get out there! There is much harder stuff I wouldn't be able to do in my little jeep also. Seems like that area is evolving, always something new I haven't seen. Its really fun area tho, Im lucky its only 30 minutes from my house
flash2pablo
NAXJA Forum User
- Location
- Vancouver, WA
Pulled and replaced the harmonic balancer trying to kill a belt squeak. So far so good.
farmer xj
NAXJA Forum User
- Location
- now in spokane WA
I picked up some new in box ACOS on CL for dirt cheap. ill add them to my pile of yet to be installed parts.....
- Location
- Vancouver, WA
Think of how good they would look on my jeep.... :wave:
farmer xj
NAXJA Forum User
- Location
- now in spokane WA
i still have dreams of actually installing everything lol same guy had some rough stuff frame stiffeners for half of cost..... If i ever close on my house with my 1500sq ft garage ill be installing things .. i may even go grab them frame stiffeners and learn to weld lol
Nice job! It's a pretty simple, but effective mod.
