What did you do to your XJ today

[jonesinxj]

lol well you still are welcome to wheel with us even though your going through a mid jeep crisis lol you know cj5 and cj7 have frames and v8 as well right?

Scouts are way better!! You don't see them everywhere!

Contests man! Let me know if you need a had with anything

 

[larsen]

Scouts are what? Is this NAISA? "Geeze"

 

[AwesomeXJ]

Used the jeep as an excuse to be late to work this morning

 

[XJOFFROAD]

lol well you still are welcome to wheel with us even though your going through a mid jeep crisis lol you know cj5 and cj7 have frames and v8 as well right?

this is true but people want WAY to much for them. I have d44's with detroits and a 345 small block, d300 transfer case, removable top with a frame for right around $800

Scouts are way better!! You don't see them everywhere!

Contests man! Let me know if you need a had with anything

yes you dont see them.

Scouts are what? Is this NAISA? "Geeze"

stick to your unibody and you will see how bad you will hate them "if" you actually wheel them over time...............

 

[larsen]

... stick your unibody and you will see how bad you will hate them "if" you actually wheel them over time...............

I always mig the unibody using the lower heat settings *snicker* Don't make me build a frame! :laugh:

 

[XJOFFROAD]

I always mig the unibody using the lower heat settings *snicker* Don't make me build a frame! :laugh:

thats the only way that i have found to weld to a unibody.

 

[crazymoose1990]

Yeah weld, bolt and plate. I know at some point my Jeep will be done for. The good thing is that I can swap all my chit over to a CJ pretty easy. I have an XJ now so until I kill this thing I am in for the long haul. Besides I have seen full frames with cracks also.
Although I do miss my CJ especially in the summer I really liked the short wheel base however with the GF and two dogs my XJ is a little bigger the down side is she doesnt like to wheel so its kind of pointless unless you count our trips to Sisters or MT hood.

 

[dellstopjeep]

I wanted to help stabilize my vehicle more since I cant do anything about my tsmall p....I mean trackbar. So i built a bracket for my stabilizer. Im sure it wont last but it helps on road manners now. It looks like I cant cut straight but I assure you thats just the camera angle.

 

[AwesomeXJ]

looks good Eric

 

[RedJeep2.0]

 

[jonesinxj]

sad day man!!!

 

[BigDog]

At this rate we are going to run out of xj's

 

[Mnkyboy]

What an honor,your jeep was chosen by the claw!!!!

 

[muddypunk]

So I am helping a buddy put jks adjustable uppers on and ACOS so his rig is going to sit right about 7" I could use help on how long to make them .Anything would help thanx :greensmok

never mind I found it finaly

 

[FiveNdime]

A moment of silence please :tear:

 

[Sideshow]

What an honor,your jeep was chosen by the claw!!!!

:roflmao:

 

[FiveNdime]

Made some mods that JCR should do to there bumper anyway.

I did this to tie in the tank skid plate to the bumper so it will be much stronger.

 

[mojojojo]

Finaly dropped the belly pan, tightened up the joints, and did a tranny service after putting it off for the last year.

started at 130 this afternoon, walked in the door about 1230am. Hit a snag at just about every point possible.

-Placed jacks to close together - had to remove one long arm in order to remove the belly pan
-Couldn't get dipstick tube out
-Got the wrong filter / gasket
-Installed trans pan - forgot filter :doh:
-forgot grease gun at home
-Installed one long arm upside down - had to remove and flip
-Took 3 hours of cussing and kicking to get the uppers to line up with the last bolt hole.:badpc:



:banghead: AAAAAAAAAARRRRRRRRGGGGGG!!!!!!!!!

 

[Avanteone]

At this rate we are going to run out of xj's

They made like 1.4 million of them, I think we're ok for a while.

 

[NW-ZJ-SCOTT]

Finaly dropped the belly pan, tightened up the joints, and did a tranny service after putting it off for the last year.

started at 130 this afternoon, walked in the door about 1230am. Hit a snag at just about every point possible.

-Placed jacks to close together - had to remove one long arm in order to remove the belly pan
-Couldn't get dipstick tube out
-Got the wrong filter / gasket
-Installed trans pan - forgot filter :doh:
-forgot grease gun at home
-Installed one long arm upside down - had to remove and flip
-Took 3 hours of cussing and kicking to get the uppers to line up with the last bolt hole.:badpc:



:banghead: AAAAAAAAAARRRRRRRRGGGGGG!!!!!!!!!

dammit man.. I forgot..