So Cal desert rats

All i have to say is, Thank god i did a tune-up on my heep..We did alot of driving... Now i need to start on the wifes jeep today..Yes i am getting around 22 MPG..I didn't think of fuel all day till we got dinner after coming down hwy 38..Then i only added 20 bucks
 
Hard to see, but they are birds..LOTS of them
091.jpg
 
I just got done washing my heep..I have new marks inside of my rims:wow:.The face, lost caps on lug nuts...LOL..Mirror on driveside is also broke..Couldn't see this with all the mud on it last night..But this is a easy fix, i am going to change doors..LOL..:clap:
 
well just crawled under my jeep to tighen everything to see if i could diagnose whats makin my jeep vibrate. found out all my longarms and tires are tight, so i jacked up the pumpkin and saw that the axle tube is slipping/wiggling in and out of the differential housing. all the welds that hold it in place broke. glad i got my new axle and truss goin in hahaha
 
After you weld the old tubes you will not have a problem..You can run it that way in my yard..After you get done with the old set-up(front axle) drop it off at my place..If it still has all the gears and stuff in it..Somebody will need parts or a axle sooner or later..I have a parts jeep that just about done..I need to find me another free parts jeep
 
Well I still got a leak at my thermastat housing on the bottom of it.... I don't know if it's a good idea but should I use some kinda sealer on the gasket? You think my BRX hoses flow too much and I need a high flow housing? It's really starting to piss me off since I JUST replaced it last week for that same problem!
 
tone said:
Well I still got a leak at my thermastat housing on the bottom of it.... I don't know if it's a good idea but should I use some kinda sealer on the gasket? You think my BRX hoses flow too much and I need a high flow housing? It's really starting to piss me off since I JUST replaced it last week for that same problem!
Click to expand...

Clean the housing...
Clean the block...
De-grease BOTH...
Get a new gasket & some Indian Head sealer...
Then put it back together...

Curt
 
scottmcneal said:
After you weld the old tubes you will not have a problem..You can run it that way in my yard..After you get done with the old set-up(front axle) drop it off at my place..If it still has all the gears and stuff in it..Somebody will need parts or a axle sooner or later..I have a parts jeep that just about done..I need to find me another free parts jeep
Click to expand...


will do. always good to recycle parts to the locals haha probably gunna go get it welded tomorrow n take it easy until the night run.

also the new axle i bought came with stock 94 lca's bushing are in great condition, steering, steering stabilizer and tracbar. if anyone needs those there at my house. all for a cherokee.
 
Last edited:
Nothing, I can hardly move. I'm down for a few days.
 
We have sponsors on here that have good prices..I think they give a discount if your are a paying member(red letter)..But if i was you i would go with 488's..I'm running them on 33's right now, but i plan on 35's down the road..
 
You must log in or register to reply here.

Similar threads

P
My Never Ending Overheating Problem
2
Replies
20
Views
1K
azupcountry
A
B
Halo Master Chief Cherokee XJ Build
Replies
11
Views
2K
Bpebler
B
N
2000 XJ, high miles, lots of new parts, still have vibration
Replies
10
Views
2K
N8N_99xj
N
Cottontail
Alarm
Replies
14
Views
2K
Rob Mayercik
R
C
New Jeep...new problems!
Replies
0
Views
471
CheapJerokee
C
Back
Top