knucklehead 61
NAXJA Forum User
- Location
- Cottage Grove, Oregon
** The official date is Saturday, Jan 28th. **
Official time is 12 noon until whenever, come earlier if you have a large project.
-----------------------------------------------------------------------------
since it has been nearly forever since there has been a south bay meet & greet i think it is time to set one up. party1
arty1arty1arty1arty1arty1:
so...
it will be at the fun factory (my house / shop) in north east san jose.
15287 penitencia creek rd. san jose 95132
(just across the bridge of death, enter at your own risk!)
i have parking for about 50 rigs or so, so thats not an issue.
bring your own beer / booze / liquid refreshments, & what ever food / snacks / appetizers you want to share. i have a fridge & micro-nuker in the factory.
as always, i will be working in the shop & will probably be doing some type of welding, so this will also be an open build party for anyone who wants to work on their junk.
it sounds like we have at least one guy who wants to do a gear swap & yes, i have a press, dial indicators, gear marking yellow snot, a d-30 case spreader, & everything else needed to do....well, just about anything.
but i hate getting that messy, so you get to do all the dirty work. i'll watch, make fun of you, & do any welding needed.
NOTE: NEW FUN FACTORY RULES!
don't dump your used oil all over the ground & my snap-on floor jack ($$$) like the last bozo i let swap gears at my shop. he almost blew it for everyone, i seriously was considering not letting anyone else but a couple close friends work on their junk in the fun factory ever again.
he didn't even apologize or help clean up. i was pissed but didn't say anything, i just cleaned up his giant mess myself. this will not happen again or you will be perma-banned from my shop! i typically do not charge for my services (but will gladly accept donations for shop supplies) so don't abuse it!
now for the date: vote in the poll to determine the date.
for a time, how about noon till whenever. if you have a longer project in mind (like swapping an axle housing, gears, or a lift kit) you can start as early as 8:00 am as i'll be out there working on my junk, & stay till it is done. i typically close up around 9:00 on saturdays so there is lots of time to get-er-done! :gee:
Official time is 12 noon until whenever, come earlier if you have a large project.
-----------------------------------------------------------------------------
since it has been nearly forever since there has been a south bay meet & greet i think it is time to set one up. party1
arty1arty1arty1arty1arty1:so...
it will be at the fun factory (my house / shop) in north east san jose.
15287 penitencia creek rd. san jose 95132
(just across the bridge of death, enter at your own risk!)
i have parking for about 50 rigs or so, so thats not an issue.
bring your own beer / booze / liquid refreshments, & what ever food / snacks / appetizers you want to share. i have a fridge & micro-nuker in the factory.
as always, i will be working in the shop & will probably be doing some type of welding, so this will also be an open build party for anyone who wants to work on their junk.
it sounds like we have at least one guy who wants to do a gear swap & yes, i have a press, dial indicators, gear marking yellow snot, a d-30 case spreader, & everything else needed to do....well, just about anything.
but i hate getting that messy, so you get to do all the dirty work. i'll watch, make fun of you, & do any welding needed.
NOTE: NEW FUN FACTORY RULES!
don't dump your used oil all over the ground & my snap-on floor jack ($$$) like the last bozo i let swap gears at my shop. he almost blew it for everyone, i seriously was considering not letting anyone else but a couple close friends work on their junk in the fun factory ever again.
he didn't even apologize or help clean up. i was pissed but didn't say anything, i just cleaned up his giant mess myself. this will not happen again or you will be perma-banned from my shop! i typically do not charge for my services (but will gladly accept donations for shop supplies) so don't abuse it!
now for the date: vote in the poll to determine the date.
for a time, how about noon till whenever. if you have a longer project in mind (like swapping an axle housing, gears, or a lift kit) you can start as early as 8:00 am as i'll be out there working on my junk, & stay till it is done. i typically close up around 9:00 on saturdays so there is lots of time to get-er-done! :gee:
Last edited by a moderator:
) I can imagine it ain't fun having your beard catch on fire. A guy my brother once worked for was doing a vertical weld on the side of a dump bed above his head. A large blob of slag fell off and went inside his clothing and burned EVERYthing from his neck to his ankle. He wasn't having any fun with his wife for a few days after that. :roflmao:
