NEW Fab 9" HD housing Bling & Strong

[RWKHausSupply]

http://www.cachassisworks.com/p-730-fab9-ms-no-brackets-3-tubes.aspx

The above without ends on it. It is currently 65" end to end of tube.

Complete housing is .25 wall and tubes are 3" OD.

Has a drain and fill plug welded in. All done by Chris Alston - chassisworks.

350$ as it sits.

PERFECT for a prerunner, jeepspeed, or crawler. Back braces can be added.

Can be made into what ever you what, any ratio, locker/spool, width, brakes, etc, for additional cost.

 

[Skullver]

I will be very interested once I peddle a few things, if you still have it!

 

[::War_Machine::]

How does this match up to the Currie 9" housing?

 

[RWKHausSupply]

I would say its basically the same. like asking someone how a 2011 ford diesel compares to a chevy or dodge diesel. its all a argument, about the same thing really.

 

[Peacefrog53]

I would say its basically the same. like asking someone how a 2011 ford diesel compares to a chevy or dodge diesel. its all a argument, about the same thing really.

F****d Over Rebuilt Dodge

:moon:

GO CHEVY!!

 

[Skullver]

F****d Over Rebuilt Dodge

:moon:

GO CHEVY!!

CUMMINS!

Yeah Robert, I am going to need some gears, still deciding on the ratio, and can you get hubs etc to do a full floater? And I have a 35-spline spool right now(3.25" case) but going to need something more streetable. Not going to be ready for a few weeks but definitely going to talk to you eventually and get something set up wether it is this housing if you have it, or another 9".

 

[RWKHausSupply]

Anyone?
325$

 

[jmaxj]

if you would be willing to ship, how much you think shipping would be?

 

[RWKHausSupply]

to??

prolly 60-80$ if not all the way on east coast.

 

[jmaxj]

to??

prolly 60-80$ if not all the way on east coast.

nowhere near the east coast, just utah.

if shipping is under 100 i may just have to acquire this.

i'll let you know

 

[RWKHausSupply]

nowhere near the east coast, just utah.

if shipping is under 100 i may just have to acquire this.

i'll let you know

I just picked Moab as a location in Utah, and to a commercial addy its only like 51$ to ship it to you.

 

[RWKHausSupply]

Ok well Chris bought one of the housings. Still have 4 more left...

I am going to make this very enticing here...
Willing to make this a complete SUPER STRONG, Bolt in rear axle!

Willing to Give you:
Fab 9- 9" .250 thick 3"OD housing
Housing ends 9" Big Bearing - installed
Above ends installed to make overall Pin offset & WMS +/-.625" customers spec

35spine 9" Chromoly axles (5x4.5, 5x5 & 5x5.5" pattern) Pair
Set 20 bearing kits (2)
Hardened Wheel studs
Bearing retainer plates
Bearings pressed on

Teraflex Complete Disc Brake Kit (4.5" & 5" pattern) no hoses

9" Super HD 3.25" Drop Out (1300HP rated)
9" Daytona pinion support
4.56 (Or any typical common ratio) Strong gear set
Master Install Kit
35 spline Spool (High Strength)
1330 Yoke
Setup above

~~2400$ OUT THE DOOR~~

2500$ total if you want it with Perches and shock mounts welded on. This would make it a COMPLETE BOLT IN rear end. All you would need would be the brake lines to fit your T or...

Super Strong Grizzly 35 spline locker in place of Spool + 350$

Try pricing a complete Fabricated 9" bolt in axle with the 35spline chromoly axles and disc brakes.. Your saving ALOT, Well over a 1000$...

Pay cash and get free Brake caliper hoses and disc brake cables, designed to fit a XJ, OR Get it powder coated for ~ free!

Shipping available.

 

[Skullver]

hmm, any floater set ups available? Or how about the above deal minus the 3rd, 5x5.5", width yet to be determined? That is a good deal!

 

[RWKHausSupply]

Chris, told ya just let me know when your ready and what you need...

 

[Skullver]

Chris, told ya just let me know when your ready and what you need...

Will do, have to get rid of a couple trucks, then build my new front end, then I will know the width, a few weeks or months most likely! Thanks!