Safari rack, lights, etc.

Surco 45" x 60" Safari Rack #S4560 Lists on Summit for $266.95 http://www.summitracing.com/parts/SUR-S4560/
Surco 48" Support Bars #S48 Lists on Summit for $ 71.95/pair http://www.summitracing.com/parts/SUR-S48/
Surco Jeep Roof Rail Mounts #J100 Lists on Summit for $ 56.95/set http://www.summitracing.com/parts/SUR-J100/
Fabricated 3/16" steel light mounts for rack--(Surco LT100 light mounts for comparison price) Lists on Summit for $ 42.95x2=$85.90 http://www.summitracing.com/parts/SUR-LT100/
KC Hilites 6x9 100 watt chrome light kit pair #240 Lists on Summit for $163.99/pair x 2=$327.98 http://www.summitracing.com/parts/KCC-240/
Basket is wired for lights with a 5-pole trailer connector so it can be disconnected for removal or so you don't have wiring running into the vehicle all the time. I have 4 hard plastic desert camo kc brand covers on the lights now, and also have 4 kc brand soft covers (black with red letters) to go with them. One light has cracked glass, but I have ordered the replacement lens from KC. Have 2 NIB gaskets for KC lenses and 2 Hella 100 watt H3 bulbs for replacements. 2 lights have original bulbs and 2 have Hellas. I have 2 relays, all wiring, and 2 KC illuminated switches in a switch panel that all will be removed from my Jeep upon sale. Surco makes a ton of accessories for their racks, and most of it can be gotten through Summit. Check out their products here: http://www.surcoinc.com/R-BRacc.html Total price for this setup new would be $809.73 + shipping. I'd like to get $500 for the whole package. Willing to ship on your dime. Might consider splitting it up...make me an offer I can't refuse. Located in Brandon, MS 39042.
These aren't the best pics, but it's all I could find on my photobucket account. I can take better, more detailed pics if anyone needs them.

I don't have a spare tire carrier for this rack. I just drilled a hole in one of the floor panels and put a piece of large allthread through it and the spare. It is sturdy enough for my light wheeling, but would need something more substantial (steel reinforcement) for hard wheeling.


Pics of the lighting connector:

Price dropped to $450...or make an offer on just the rack, 2 lights, 4 lights, or any combination of the above!!

Bump for drop to $400. Will separate, too!!

Final drop to $350. I'll keep it if it doesn't go for that...but I'm sure somebody needs a good rack or some KC Lites.

Bumpit.

this is a pretty good price folks.

Thanks for the bump. Gonna try to get some better pics this weekend. I have it off the XJ and sitting in my garage.

Hmm, very tempting. Could you get me a shipping quote, or ballpark, to Huntsville, 35805?

Sorry it took so long, Minagera. Shipping to 35805 (would need to be a business or you could pick it up at trucking terminal) would be about $100. Probably would be less, but wouldn't know until actual time of shipment. I wouldnt' mark shipping up any. What I'd pay, you'd pay.

you're going to have to disassemble the rack to get it shipped reasonably.

a guy in kansas bought mine and freight without taking it apart was 130 or so.


after i took it apart it was only about 30 bucks to ship.

Surco racks don't disassemble.

Also found mounts for Yakima/Thule bars that will go with it as well.

601cherokee said:

Surco racks don't disassemble.

Click to expand...

huh???

look closer.

there are screws in four of the square joining plates. only on one side. the other side is riveted.

then of course the flat center floor peices un screw at the ends.

I'll be danged. I never noticed those screws before. Had to come home and look at mine to be sure, but it apparently will come apart. Might have to take it apart this weekend and see how small it will get for shipping and weigh it properly to get a better price on shipping. Thanks for opening my eyes, Wingnutooa. BTW, what happened to all the powdercoat on yours?

price shipped to 99502 (its alaska so i know shipping is going to rape me)

601cherokee said:

Also found mounts for Yakima/Thule bars that will go with it as well.

Click to expand...

Can you get a picture of those, would you be willing to separate/price?

601cherokee said:

I'll be danged. I never noticed those screws before. Had to come home and look at mine to be sure, but it apparently will come apart. Might have to take it apart this weekend and see how small it will get for shipping and weigh it properly to get a better price on shipping. Thanks for opening my eyes, Wingnutooa. BTW, what happened to all the powdercoat on yours?

Click to expand...

my guess is its just old...

when i shipped mine i got it all wrapped up in cardboard i want to say about 14x8x50.

after you take it apart the longest peices are the floor "planks" which makes it a little awkward to box up but i made it work.

your's will obviously be a little bigger but not a lot.

girth should be the same but yours will definetely be longer.


when i got mine boxed up it was 30 lbs on the nose with 2 lights and brackets.

EDIT:

here's the guy that bought it.

he was lucky enough to find another trailtalk user that had some gutter mounts for sale at the same time.. score!

krnkimchi702 said:

price shipped to 99502 (its alaska so i know shipping is going to rape me)

Click to expand...

Give me until after the weekend to disassemble and weigh the whole setup. I'll try to get you a quote on Monday.

Cnickgo said:

Can you get a picture of those, would you be willing to separate/price?

Click to expand...

Will get a pic this weekend sometime. They are just 4 extruded plates that conform to the small square tube and are drilled to accept 2 u-bolts each that go around the Thule bars. And yes, I'd be willing to separate.