Search results

My 4dr was in a sort of T-Bone type of accident. The majority of the damage is to the Passenger side door. No broken glass or anything. The door is just crushed in and is difficult to open\close. Plus it doesn't close all the way due to the bow in it now. Anyway, does anyone have a door they...

My transmission died in my 90, and I got my hands on a 23 spline from a 91. I know I have to pull the input shaft on my 231 transfer case and swap it for a 23 spline version. Looking at novak-adapt, it seems that before '90 they use a "short" 1.2" shaft and post '90 they used a "medium" length...

Does anyone preferably East of the cascades have an AW4 they could sell? Ideally this would be from a 87-90. Mine finally went kaput. Thanks!

Hello all. Wondering if anyone has come across this particular issue and found a resolution. Ive found some threads searching that are similar but it seemed no resolution was found. What happens is that the Transmission when cold will seem to stick in 1st gear. The way I like to describe it is...

As an extension to a couple of threads, http://www.naxja.org/forum/showthread.php?t=1080363 http://www.naxja.org/forum/showthread.php?t=1100113 I am posting this one to provide a parts list to everyone. This parts list is something I put together to completely replace all of the parts in...

I am re-doing my AC system and I have all new hoses except for one that I cant find. This is for a 90 RENIX that originally came with R12. I am putting new hoses in to complete the all new AC system I am putting in which will now run R134a. The hose is the one that goes from the Expansion...

Recently when browsing this website, I get constant Antivirus alarms for env.nocache.js. Can the webmasters please look into this? It just started happening pretty recently on this site and happens on every page I browse here. Thanks! **EDIT** Upon further investigation it appears that...

Hey guys... im selling my used TRE Fuel Injectors. These worked great but were too big for my stroker. I purchased these brand new and put about 2000 miles on them. As soon as i pulled them i stored them in Gas. Pulled them on 10-13-12 and will store them like that until shipped. These should be...

Looking for a PSC1-002. Anyone have one they are wanting to sell? Im in Bend, Oregon Thanks!

Hey guys.. got a question for ya.. I am having a problem with my RENIX Stroker that im looking for ideas on.. I have an issue with a Lean Tip-in. Especially when at a stop and then accelerating. I know that with forced induction you can throw a 02 clamp or map clamp on it to help with...

Hello, I have my heater box down to replace the heater core and evaporator core. Ive found that the Seals / foam for the top of the heater box, blower motor area etc are no longer available. I have heard from numerous sources as well as i have read here that you can replaced those "foam"...

So i have a 90 RENIX. Im pretty versed in RENIX-ese and i have FSM;s etc. I have been chasing a low idle issue on my RENIX, and its bugging the crap out of me. Ive tested every sensor and every ground both at the ECU, and the sensor directly. The only ground that doesnt have continuity to...

Does anyone know what the output voltage is for the B+ Latched output on pin B10 at the ECU? Ive tested it at the ECU (B10), the Diagnostic Connector (D2-12) and at the B+ latch relay (pins 4 and 5) and in all places i am only reading a little over 10 volts. I suspect that this is suppose to...

Hello, I have the change out my heater core and since i also have AC i have to remove the evaporator core. This is a 90 RENIX. Please also keep in mind that this was a working R-12 system that worked great last summer. I am getting the system evacuated, but no one in town has R-12 anymore...

I have two sets (QTY = 8) of injectors for sale... ACC-150826 ACCEL 26# Injectors. 6 of them have approx 2000 miles on them, and the other two have 0 miles on them. They work great... just are too large for my stroker. http://www.summitracing.com/parts/ACC-150826/ I also have some stock...

Probably a stupid question ... but how do you get the orings and spacer out of the quick disconnect's from a 91-95 cherokee. In my 90, you could just get in there with a screwdriver and dig them out... but with these plastic ones it looks like there is a black spinner thing in the way that wont...

Does anyone have any recommendations as far as finding a good stock replacement camshaft?? Or even a used one that is in very good shape. Were talking with stock specs and lobe width. Thanks very much for your time.

Just as the title of this thread states.. Im looking to find / replace the gaskets that go between the door handle and the door. Im swaping out my old faded handles with some Chrome ones i got at the JY. The ones i picked up have fairly decent gaskets on them... but i figure while i got it all...

I just bought a dana 44 out of an 87 at the u-pull-it. It has 3.07 gears according to the tag on it (and it was a manual transmission). I have been searching on here, and i cant seem too find too much information on what i should consider doing to this thing. Besides of course changing the...

I know for the AW4 its recommended to stay away from synthetics and the like and stick with the recommended Dex/Merc. However, what does everyone recommend for brake fluid, and power steering fluid? Just stick with manufacturers recommendations? Ive even heard some here using ATF in the...