Search results

I need to get rid of her to get a new car, just don't wheel much anymore and don't have time to do the engine work it needs. Below are the specs. • Rock Krawler Long arms • Rock Krawler 8" coil springs • Alcan custom leafsprings • JKS adjustable coil spacer • Ballistic Fabrication coil spring...

$100 OBO Cleaning out the garage and need to get rid of a D44 30 spline, full spool. It is in perfect condition. $100 OBO help me get rid of this guy. Can email Image. Contact me at [email protected] Also have a set of JKS quick disconnect links don't have the axle pins mounts for...

I have a rear dana 44 out of a waggy w/ an arb and 4.10's. I am running wheel spacers to increase the width to help it match my hp 44 in the front. Someone offered to straight up swap me for a mini 14 bolt rear that has an arb and same gears as mine currently does. All that it needs is some...

Is anyone interested in running Chinaman next week? I was thinking of going down that way to fish, camping and fourwheel a few days during the week anyone interested running chinaman on 5/18, 5/19, or 5/20?

I have a pretty much brand new rebuild Waggy d44 rear end that I build up with the help of josh at crawler tech last summer. Bolts right into an Xj has a BRAND NEW Arb maybe engaged 4 times at most last summer and 4:10 gears with anti wrap perches and high clearance shock mounts. Shot in the...

Does anyone down south know what the weather and conditions down around the Sand Dunes are like right now? Also any clue what snow conditions around little bear and Blanca peak are?

Have a dana 30 complete and stoke I need to get out of my back drive before the weather gets to it. Also will throw in some jks disconnects. $100 and it's yours.

I need these all out of my garage asap. D30 out of 95 xj all in good working order stock 3:55 gears open. Comes w/ jks quick disco's. $200 obo 8.25 out of 95 xj also in good working order stock and comlplete except missing hard lines and e-brake lline. 3:55's $200 obo D44 full spool 30...

Like it says I am in need of a stock xj pitman arm, it would be amazing if it was reemed to 3/4" also. If you need I have a 4"(I think) drop I woulld be willing to swap you for it. Tristan

Looking for a reciever for a 95 xj, for rear tow point.

I got my tie rod made today for my hp 44 and am going to make the Track bar tomorrow. I know that I need the tires to be straight or centered for measuring from the pitman to the knuckle, it's a high steer set up. I was wondering what is the easiest way to do this? Thankx, Tristan

I am getting ready to install my rear d44 today and have to run brake lines into the drum if anyone has experience and can lend a hand on short notice that would be great I am working pretty much at broadway and beleview. just give me a call at (303) 589-3100. Thanks, Tristan

By the end of this week I will have the following off my xj and for sale D30: stock complete from hub to hub in good working condition can toss in jks quick disc. $obo 8.25: stock and complete in good working condition $obo Waggy D44: This is only the housing and inner shafts $obo Rusty's...

I am thinking about picking up two snowmobiles off a buddy. I know from what the manuals say that xj's should be able to(weight wise) pull two sleds and a trailer does anyone have any personal excperience with towing sleds with there xj, especially going up the I70 corriduor? It's a 95 xj...

I have been searching around the denver area for rattle can engine enamel in a BRIGHT yellow to paint my knuckles and sliders. I have found lots of engine enamel but in very dull yellows brightest being dupi daytona yellow. Does anyone know where has a good selection of colors around, or...

I am in the process of getting all the parts together to put my d44 in. This axle is set up for high steer. I am going with the tnt truss which will put the trac bar above the axle. I have searched and only found info on d30 high steer. So I was wondering what some options are for steering...

As stated I'm looking for a Dana44 Arb for 4:10's does anyone have one, and/or an ARB compressor? TIA

So I have reasearched and found lots of write ups on doing a rear disk conversion for xjd44 can I assume that these will work the same for the waggy d44's? If not can someone point me in the direction of a write up as I'm sure I overlooked something that includes this for waggy 44's? Also I...

Anyone running a waggy d44 can you post pictures of what your pinon angle looks like if you did not adjust the pinion angle but just set it so that you are running a good castor angle? Also after doing this would you suggest setting it so that you roll the pinon angle up and have to rotate the...

I just picked up a set of waggy d44's and was wondering if there would be anyone that would be willing to help do an install on them. They need brackets welded on the front and possibly the knuckles turned. Would anyone that has done this before be willing to help for some good beer or extra cash?