PhotoJared
NAXJA Forum User
- Location
- Las Vegas, NV
A dark brown. The grout line is only 1/8" so there won't be much. They did a great job of leveling the slab prior to installing the tile. Very minimal lipping.
Projext "V8 XJ" Build
- Thread starter PhotoJared
- Start date
A dark brown. The grout line is only 1/8" so there won't be much. They did a great job of leveling the slab prior to installing the tile. Very minimal lipping.
PhotoJared
NAXJA Forum User
- Location
- Las Vegas, NV
Appointment setup for next Tuesday for an exhaust install!
Transpoquick
NAXJA Forum User
- Location
- illinois
Cool kitchen but, aren't you worried about the cabinets being so close to the range?.
Vernicious
NAXJA Forum User
- Location
- Layton, Utah
I'm sure it's in the post somewhere... What shackle relocation brackets are those?
PhotoJared
NAXJA Forum User
- Location
- Las Vegas, NV
On the sides? No. The cabinets arent directly over the range. It's pretty standard how it is.
HD Engeneering no lifts
clydefrog
NAXJA Forum User
- Location
- Northern California
What size are you going to do? I ran 3" out from my muffler and dual 2.5" going in, pretty happy with it.
Vernicious
NAXJA Forum User
- Location
- Layton, Utah
Thanks!
PhotoJared
NAXJA Forum User
- Location
- Las Vegas, NV
Collector to 2-1 collector will be 2.25" (maybe 2.5" if it fits) then 3" all the way back.
PhotoJared
NAXJA Forum User
- Location
- Las Vegas, NV
Hey! Look what I bought!
PhotoJared
NAXJA Forum User
- Location
- Las Vegas, NV
Nice. I'm a bit surprised you didn't have one though
I keep telling you guys. I know nothing about wiring lol:doh:
PhotoJared
NAXJA Forum User
- Location
- Las Vegas, NV
So I made a $2500 mistake:
Canceled insurance on the Jeep July 2015. Registration was valid until April 2016. Never turned in the plates. $1250 fine for an uninsured vehicle and $40/mo for 3 years for SR22 high risk insurance.
**** me
Canceled insurance on the Jeep July 2015. Registration was valid until April 2016. Never turned in the plates. $1250 fine for an uninsured vehicle and $40/mo for 3 years for SR22 high risk insurance.
**** me
WTF is this bullshit? Did you get pulled over or did they just send you a notice?
PhotoJared
NAXJA Forum User
- Location
- Las Vegas, NV
cleenrob
NAXJA Forum User
- Location
- Converse TX
dirty thieving bastards
PhotoJared
NAXJA Forum User
- Location
- Las Vegas, NV
I'm just pissed that I have to carry the high risk insurance now. I've been insured just not with the Jeep. So dumb. I get it. Its my mess up and I'll own up to it. I just dont like it.
PhotoJared
NAXJA Forum User
- Location
- Las Vegas, NV
So I wired in the fuel tank trick. Oddly enough I had to use 2 470 ohm resistors for 98% tank and 1 220 ohm resistor for 50% tank.
My wiring diagram says 40 ohms for full tank and 250 for empty. I wonder if that means only 40 ohms total going to the PCM rather than 40 ohms resistance. Lesson learned.
Now another odd thing. My MIL is staying on when I put the ignition in the "on" position. Does it stay on until you start the jeep then it goes off? (I couldn't start it because it's late)
My wiring diagram says 40 ohms for full tank and 250 for empty. I wonder if that means only 40 ohms total going to the PCM rather than 40 ohms resistance. Lesson learned.
Now another odd thing. My MIL is staying on when I put the ignition in the "on" position. Does it stay on until you start the jeep then it goes off? (I couldn't start it because it's late)
