BoringDave
NAXJA Forum User
- Location
- Boring
I believe the same case with work in HP30,LP30 or a super 30. 5.38's are available for the super 30.
**NWChapter Random Thoughts Thread***
- Thread starter dick.breakey
- Start date
I believe the same case with work in HP30,LP30 or a super 30. 5.38's are available for the super 30.
- Location
- Rainy side of Washington
Yeah I know the same carrier works for hp and lp, not sure about super 30s... the lowest an hp d30 can go is 4.88 iirc. Lp d30s and super 30s can go further.
NW99XJ
NAXJA Forum User
- Location
- Gresham, Or.
WISHFUL THINKING:
- Location
- Rainy side of Washington
I'm actually kinda hoping there is aftermarket support for the diffs in the Renegade.
The body styling isn't my thing and I don't like independent suspension but with a mild lift and some aggressive tires, better gears, and possibly traction control upgrades, it could be a beast.
The body styling isn't my thing and I don't like independent suspension but with a mild lift and some aggressive tires, better gears, and possibly traction control upgrades, it could be a beast.
pnwridgerunner
NAXJA Forum User
- Location
- Vancouver,WA USA
WISHFUL THINKING:
Now that looks cool and sweet, that would be AWSOME if the aftermarket would make a lift for the new Cherokees
Demonoid369
NAXJA Forum User
- Location
- Salem, OR
Ballistic joints or Johnny joints? Got a pair of control arms off a grand Cherokee and both side are fixed rubber bushing, want to make one side a flex joint but don't know what type to get
- Location
- NE Texas
I'm a Currie JJ fan...
Demonoid369
NAXJA Forum User
- Location
- Salem, OR
Where's the cheapest for the JJ? Been looking around but can't get a good low price range for them. I know I can get weld on ballistics for 30$ a piece and I know the JJ full joint and such will be more but just trying to save a few bucks
bmikes
NAXJA Forum User
- Location
- portland or
My opinion... Don't try to save a few bucks on the suspension.. Especially on the joints. I'd get the best of what you can afford
KRG.FAB
NAXJA Forum User
- Location
- Jacksonville, FL
I don't think he's trying to cheap out on bad joints. Just trying to find the best price on the JJs
Bronzewyrm
NAXJA Forum User
- Location
- Independence,or
I have no experience with the Currie's. My 2.63 ballistic joints have held up to moderate wheeling for over 4 years now. I'm just now at the point of my first adjustment/rebuild(s) on them.
Bronze.
Bronze.
Demonoid369
NAXJA Forum User
- Location
- Salem, OR
Bingo lol just don't know where the cheapest they would be at
Demonoid369
NAXJA Forum User
- Location
- Salem, OR
Do you mean turning the adjustment ring to tighten it or are you replacing the entire guts of it? The adjustment on those is what got me curious about them
Bronzewyrm
NAXJA Forum User
- Location
- Independence,or
not sure yet. im standing at the bank, getting ready to cross that bridge...
Bronze.
stang65
NAXJA Forum User
- Location
- independence oregon
dang toll bridges always cost money
Bronzewyrm
NAXJA Forum User
- Location
- Independence,or
seriously! and at a "variable rate" Bastardos...
- Location
- Rainy side of Washington
Rustys control arm bushings are the I5 bridge of this analogy :gee:
Demonoid369
NAXJA Forum User
- Location
- Salem, OR
Got a question guys, how do you guys change your uca bushings? I've figured it's either a drop the axle scenario or just disconnect the uppers from the axle, but then again..... That would be too easy lol
Also to get the bushing out, hammer them out or???
Also to get the bushing out, hammer them out or???
- Location
- NE Texas
-Easiest is Axle out with a big hammer
-Doable is Axle In with a Ball joint press kit.
- Location
- Rainy side of Washington
Burn or drill rubber out, sawzall a slit in the outer bushing sleeve, collapse it with a chisel.
Wirebrush the shit out of the opening, then balljoint press to put the new one in. Careful you don't collapse the passenger mount, its just a c shaped piece of sheetmetal. Get the zoneoffroad UCA mount boxing plate (or fab one yourself if you would rather spend time than money) and weld it on while the bushing is out if you're feeling frisky.
http://zoneoffroad.com/zone-offroad...pport-gusset-cherokee-xj-zj-wrangler-tj/j5013
Wirebrush the shit out of the opening, then balljoint press to put the new one in. Careful you don't collapse the passenger mount, its just a c shaped piece of sheetmetal. Get the zoneoffroad UCA mount boxing plate (or fab one yourself if you would rather spend time than money) and weld it on while the bushing is out if you're feeling frisky.
http://zoneoffroad.com/zone-offroad...pport-gusset-cherokee-xj-zj-wrangler-tj/j5013
Similar threads
