Follow along with the video below to see how to install our site as a web app on your home screen.
Note: This feature may not be available in some browsers.
Welcome to the new NAXJA Forum!
If your password does not work, please use "Forgot your password?" link on the log-in page.
Please feel free to reach out to [email protected] if we can provide any assistance.
Repirs made:greensmok
Jeep is back up and running. BAd Crank Sensor.
Ohm'd out at 220 cold ran until cut off then read infinity.
I must have been :roll: :wierd: :speepin: last time I was checking it over.
Odd that it ran on starting fluid once it died when I check it on the side of the...
I checked the crank position sensor individually for ohm reading and voltage in - out. I got the readings didn't change or differ when it would run / not run. I forget the readings now.
Another friend stoppedby and changed out the coil and module beneath it with a spare. (No change).
I'd...
Update:
Jeep will run 2-12 min. Now it is loosing Injector signal & spark.
Signal and spark will return once cool.
Fuel Psi is good. I couldn't find a cam position sensor.
Looking to change out the dist ignition module tomorrow.
Friends Mom's 1989 Cherokee 4.0L auto 165k died.
Any help / advice / thoguhts would be greatly apreciated.
I picked it up with the trailer this evening (Saturday) and took it home. The Jeep will restart once cold (2-3 hrs). Upon restart it will cut off after 2-3 min. Once dead, turn off...
Disconnected, My XJ with 3" Ruff Country stuffs the 27"SSR's into the fenders, The fenders are now clearanced about 2 inches just form tire rub (no flares). This thing flexes like mad up front. This flex also crushed a tranny line on the pass side. (I'll be adding 2" spacers and 2" taller...
How did those Super Swamper LTB's ride and balance out. I just can't help but look a the new 33x13.50-15 for $118.50 For that price it's a steal even for an old school Bias Ply Polyester Mud grip.
I like the Super Swamper Boggers best! Down here on the fall line near the coast if it's not dry it's bottomless. They handle mud the best and everything else at an acceptable level. These tires also work well for scaring small children, but my three year old likes to climb on mine. If I...
I have heard of a nice piece produced by Carolinia rock shop using ramcharger ends, But I have not seen it and can't seem to find any more info.
As far as the factory inverted Y, nomatter how you bend it the geometry from point a to point b will be the same and with greater lifts, bump steer...
:eek: Ohh Yea !!!! Now that's waht i'm looking for, Nice, simple, cheap Home brew spring mod that is Very functional.
Awsome excellent work...
Now for 20 questions: Ok maybe only 7.
1. Half ton 2wd Chev???
2.What legnth eye to eye?
3.What year?
4. Any ideia the rear GVW of the...
:eek: Haa ha I just looked and you are in Richmond, I'm stuck here in Richmond too (DuPont Spruance). Just let me know what you need bent, maybe I can hook you up, I've got a machinist friend in Richmond at Alcoa but I did my exhaust work in Prince George... I also went to school with a guy...
How To Bend Tube NAXJA
NAXJA HOW TO BEND TUBE NAXJA
Helpful tools:
Marker, Tube degree wheel, Pipe cutter, Level, Gloves
And a nice $7,000 240v Bend Pac hydrolic tube bender
Usually exhaust bent by card is bent from left to right in such a way that the tube is...
Edited to include trans and engine size.
Mine is a 1991 XJ, 4dr, 4wd, 4.0HO, Auto?, NP 231, Chy-8.25.
Front Drive Shaft Legnth = Rear Drive Shaft Legnth =
I have not even considered the Front drive shaft. I didn't even realize that they are close in legnth. :eek:
Maybe we should include the front also ???