Recent content by Atom

I bought a new rotor and new cap as well as the sensor that goes on the bottom of the rotor. I still had that clicking noise... So I checked every XJ I could and found that the 3 other 1996s I checked had the same clicking noise. So that was 20 K miles ago and I still have that noise but the...

anyone....... anyone........

Swapping in a 93 non disco dana 30 into a 91 MJ with disco. What do we do with the Vacum lines on the MJ? Plug them or what. TIA Jori

I ran it for a few years out of a 91 exploder. All exploder 8.8 rear ends had 31 spline, but not all rangers. Pretty easy swap, stronger than 8.25, and I believe even stronger than D44.

This is not my own shame-less plug, but I do know the guy who built these. If I could afford this supercharger..its what I would buy. Check out this link: http://www.rockcrawler.com/features/newsshorts/01july/avenger.asp Ed has been building these for over 5 years now and the newest ones are...

Does anyone know what the torque spec is on the frount output shaft yolk nut? My seal was leaking from a bad vibration I had when I put the frount pinion at a bad angle, so I put a new one in today. (Please no FSM links!!!!) Also there seems to be a o-ring instead of a washer between the yolk...

On my 96 xj Dana 30 high pinion I put in new gears and the seal started leaking. I took it appart and no problems with the shaft or the seal. So I replaced it anyways. The new seal leaked right away. It leaked a drop a night for about two weeks and then just stopped. I don't know what it was...

My 1996 xj would not start. It cranked but would not ever run. I had a long post last week and finally figured it out. I replaced ignition, CPS, and Coil but still had no spark. Search under " Cranks but won't fire, Neutral safety switch?" for the whole progression. I think the key thing was...

Went out to work on it tonight and it has spark from coil. I connected it to the distribitor and the jeep started right up??????? I guess I will drive it until it happens again what else can I do? Could the computer have reset its self after I let it set for about 48 hours? I did nothing to it...

Fuel pump is pumping- the fuel rail has up to 50psi of pressure and it builds back up when all the pressure is released. I check the fuses by swapping them all out one by one. All the relays work too, checked them by swapping them too... I am just checking all the sensors one by one with the...

Thanks for all the info! I did check all the relays and the fuses and they are fine. I will check the wiring next and I have a good book to go through and check all of the sensors. ONE NEW THING- When I turn on the key the electric fan runs??? I don't remember it working like that in the past...

On a 1991-1997 you can get the codes out of a computer by cycling the key three times and then watching the check engine light flashes. Mine has no trouble codes in it at all so that wont help. BUT, I did have a trouble code about a month ago and I dont know if it could be invloved in this...

The jeep is a 1996 4.0- for those whom wanted to know. Has anyone ever bought a new coil and or CPS that did not work? (B.T.W. I have replaced both and it did not fix it- trail spairs right?) Does anyone know anything else that could cause no spark? 1. Crankshaft postition sensor is new 2...

Ok this is what I got… Jeep started dieing on me for no reason and then twenty minutes latter it would start right back up and then go for a few days. Now its in my garage and wont start at all. It cranks but wont start. I put a CPS in it as some people posted. Still wont start, so I put in a...

I have done a search and no one has any info to help me! Is there any pointers that anyone can give me to help me get the rubber insert into the "cup" on the bottom of the tank. I have a book that shows a picture and I have felt it with my hand- I just cant get it lined up right??? Does the tabs...