Search results

I've been getting some squealing from my front disk brakes on my '96, so I went to take a look at them today. Oddly, only 1 of the 4 pads was seriously worn. The inside driver's side pad was completely gone, all the others had quite a bit of pad left. I don't know a whole lot about brakes...

Hi everyone! Being from Vegas I don't visit this forum often, but I'm going to be heading to Granby, CO for a freinds wedding this September and was wondering if anyone can suggest any good places to do some offroading. I'm only running 31's with a 3+" lift, but I'm locked rear and have plenty...

I've got a '96 with stock rear driveshaft and NP231 Transfer case. I need to drive for a while without the rear shaft on the vehicle. I've read posts, and seen products (plugzit) that seem to suggest that oil can leak out if the shaft is removed. Now that I've removed my shaft, that...

In Las Vegas: 3.55 gears w/ carrier for HP Dana 30 3.55 gears w/ carrier for Chry. 8.25 27Spline (2) 27 Spline Shafts for Chry 8.25 All used in good shape <100K. $50 for any item (that's $100 for both shafts.) Will ship. Matt

I guess its time to learn about the fuel system. I was welding on the rear passenger side floor of my 1996 XJ (the fuel tank was still in, bad idea maybe?.) Now when I run it I seem to have a problem with my fuel pump. It all works fine but it makes an awful electrical buzzing sound. The...

I decided that I'm going to have a shop set up my R&P gears. I'm concerned because the folks at the shop where I normally have my drive line work done are telling me that to go from a 3.55 to 4.56 I do not need a new carrier. This seems contrary to what other shops are telling me. The...

I'm going to be rear gearing my front end, but before I do there seems to be a problem I need to correct. When I'm in 4wd (hi or low), going up hill and really putting out a lot of torque, I get a whap, whap, whap sound from the front end (like its bucking.) It sound almost suspension like...

I'm looking at installing new gears and a rear auburn limited slip in my '96 cherokee, automatic. Having never done this before, I was thinking of having the gears set up at a shop. What I'm finding though is that it's going to cost $800 to have $700 dollars worth of parts put on. One, is...

In the past couple days I've turned my headlights on with the jeep off. It seems after about five minutes of running low beams my battery can't turn over the engine anymore. Twice I've had to jump start it. I've got a cheap walmart battery so I'm planning on replacing it with an Optima Red...

So I fabricated some rock sliders for my XJ (pretty much identical to the ORGS super nerfs.) I decided that for the frame rail attachment, the self tapping bolts into the outboard side of the rail would be plenty strong. Only problem is: now that I'm ready to bolt them up, I can't find any...

I've been 4 wheeling for about 8yrs and have never been part of a club or participated in "organized" events. A friend and I are thinking of changing that by going out to Panamint Valley Days this year. Being from Las Vegas we've done quite a bit off offroading out in Death Valley. I was just...

I've been running a 3" lift with a full replacement spring pack in the rear for about 2.5 yrs. About 12 months ago I put on 31x10.5" tires. Unfortuantly the rear tires have been chewing up the wheel wells (I've got skid marks on the inside walls and the rear fender is all torn up. Before I...

I'm about to replace the trackbar on my '96 cherokee. I'm looking for an adjustable one since I've got a 3.5" of lift. Anyone have any suggestions? I'm leaning towards Rusty's Offroad since that's where my lift is from. Also i need to replace my motor mounts (driver side is destroyed.)...

I need to replace the fan clutch on my '96 Cherokee I6 4.0. I went over to Autozone and picked one up for $38. Unfortuantly it's a 1/4" too long to fit between the radiator and mounting studs. Someone said that Car Quest sells one that fits, but they turned out to carry the same one as...