looks like I waited a bit too long for my stiffeners....

[rockclimber]

found this today.

gonna weld it, plate it, and then put the stiffeners on... hopefully I can get it all done today.

 

[souske]

Its probably fine....

:sure:

 

[Vanimal]

ouch. yea, i gotta plate that area too before mine cracks. sides are plated but i havent gotten to the bottom yet.

 

[GSequoia]

Just put the sway bar back on, then you won't see it anymore.

 

[jeeperjohn]

I had a bunch of cracks in mine when my stiffeners went on but they weren't enough. I think if took the cage out of my junk it would collapse in on itself.

 

[rockclimber]

crisis averted...for now.

started prepping for the stiffeners. I won't have time to do them today, but I can get all the undercoating off now, and I think I have wednesday off so I'll get them done then.

 

[GrimmJeeper]

before you plate over that crack drill a hole in the end of the smaller one where it comes away from the bolt hole (left side of the pic) this will help keep it from spreading further without you being able to see it. The rule of thumb for welding up cracks is to drill a small (1/8" or so) hole in the very end of each end of the crack then weld it up and grind it smooth.

 

[GrimmJeeper]

damn just a little too late with my post.

 

[rockclimber]

before you plate over that crack drill a hole in the end of the smaller one where it comes away from the bolt hole (left side of the pic) this will help keep it from spreading further without you being able to see it. The rule of thumb for welding up cracks is to drill a small (1/8" or so) hole in the very end of each end of the crack then weld it up and grind it smooth.

I did that. I've seen you post about it before. I just didn't snap any pics.

 

[Vanimal]

I had a bunch of cracks in mine when my stiffeners went on but they weren't enough. I think if took the cage out of my junk it would collapse in on itself.

haha definitely, you got some good cracks in that thing.

i got my stiffeners on pretty soon into my "wheeling career", however i do have 2 nice sized cracks in the floor under the rear seat. thankfully that's it so far though.

 

[GrimmJeeper]

I did that. I've seen you post about it before. I just didn't snap any pics.

right on :thumbup:

 

[boostamante]

What a pain in the ass it is to plate the whole side of the jeep... not fun!

 

[rockclimber]

What a pain in the ass it is to plate the whole side of the jeep... not fun!

yep... after this crack, I want to plate the bottom of it as well...not looking forward to all that overhead welding...

 

[Vanimal]

i've been putting it off, but between you and Julio, i think i've seen enough to convince me to get on it.

 

[boostamante]

Overhead welding isn't too bad but if i were to do it all again, I would wear full leathers...lol

I hate the bits that fall and burn you in places you least expect.

 

[souske]

That wouldnt happen if you welded in something other than,assless chaps

 

[SC Rednek]

I did this exact fix last week, except I caught the crack in mine a little earlier.

Those cracks under the rear seat are getting really bad, I need to brace that up soon.

 

[Vanimal]

I did this exact fix last week, except I caught the crack in mine a little earlier.

Those cracks under the rear seat are getting really bad, I need to brace that up soon.

still trying to figure out how to tackle that one. i can fix the cracks, but seems like it's trying to cure cancer with advil. i figured a cage would help.

 

[Skwerly]

Whew, I was going to say the same thing about drilling a hole. Excellent.

 

[tone]

still trying to figure out how to tackle that one. i can fix the cracks, but seems like it's trying to cure cancer with advil. i figured a cage would help.

when in doubt, cage it out!


:clap: