Recent content by outracing

  1. O

    Np242j HnT kit

    That will be most helpful! Thank you!
  2. O

    Np242j HnT kit

    Are the 231 and 242 HnT kits the same?
  3. O

    Np242j HnT kit

    I had a 98 before with an np231 transfer case. It only had a 3-inch lift, but I kept managing to break the yoke on the rear drive shaft at the axle side. I ended up installing degree shims as well which helped with the issue, but it still had some massive vibration on the highway.
  4. O

    Np242j HnT kit

    I was able to find that Tom Woods stuff, I was just really looking for a hack and tap kit
  5. O

    Np242j HnT kit

    Hello everyone, I just purchased a 1998 Jeep Cherokee Limited. It is a very nice vehicle with a hundred thousand miles. I would like to lift it 4 and 1/2 inches. With that size lift, I know that I will need to lengthen my drive shaft. My issue is, when I look at full SYE kits or HnT kits there...
  6. O

    P0700 & P0705 with shift lever issue

    In case somebody else looks at this someday; I ended up removing the center console from the Jeep, but there was no adjustments to be made at the shifter. I crawled underneath the Jeep it was able to pop the center out of the shifter Link cable just a little bit back from the transmission with...
  7. O

    P0700 & P0705 with shift lever issue

    Well, I inspected the cables at both ends. Nothing seems to be array. I just replaced the neutral safety switch and cleared the codes but they immediately came back. I guess I will have to do some more investigating on how to potentially adjust this shifter linkage cable
  8. O

    P0700 & P0705 with shift lever issue

    Hi everyone, so after searching around on here I haven't quite been able to find somebody who posted a similar issue. I just purchased a 1998 Jeep Cherokee Limited. The weird issue that I am having is; the check engine light is not on, but when I took it down for inspection to get the new...
  9. O

    99 Cherokee 3" or 3.25" rotors via vin number?

    Chickenbot, thanks so much, I've been trying to find that info for awhile now. With a build date in 98, it seams as though I should be looking at the 3.5 inch set up that Matches the 1998 and 1999 model years instead of the 2000 and 1999. Guess I have some more figuring to do. Tim_MN, I have...
  10. O

    99 Cherokee 3" or 3.25" rotors via vin number?

    I went to my local dealer. They refused to print / look up anything for me. What I just did was measure the lugs in the wheel hub. They are the same length as the ones for the 2000 Cherokee. AutoZone only lists one part number for the 2000 Jeep Cherokee and it matches one of the part numbers...
  11. O

    99 Cherokee 3" or 3.25" rotors via vin number?

    sinat01, My door on the driver side got hit a while back and was replaced. The build sticker is now gone. That is why I was really hoping that I could learn with my VIN number. I guess I'll be buying the sub par parts at Autozone since I'll have to pull them and match them up. I really...
  12. O

    99 Cherokee 3" or 3.25" rotors via vin number?

    Hey all, I have a 1999 SE. I want to replace the front rotors on it, but I can't tell if I need the 3 or 3 1/4 inch rotors. Is there a place I can input my vin and find out what I have? This is proving to be a bit frustrating. Thanks for your help! -Jason 1J4FF28S3XL573049
  13. O

    99 XJ Bucket Seat Replacement

    Me too. Bump post back from the dead.
  14. O

    engine dies when heat/ac is turned on?

    So apparently quite a few people are having the same issue as I was so long ago. It is been awhile since I have logged onto this forum and apologize for not posting what was my final fix. The PCM in my beloved XJ head finally bit the Dust. After countless hours of research and talking to...
  15. O

    Let me see your light bars

    5-Speed, those back up lights are sweet! Where did you find those? You don't need a relay switch for them do you?
See more
Back
Top