Recent content by nateofmt1

  1. N

    Using a high low adapter

    It works just fine upside down. Thanks for your insights.
  2. N

    Undercarriage Cleaning

    Oven cleaner won't peel off paint or other things like wire coatings?
  3. N

    Floor repair

    I noticed that, behind the driver's wheel, the curve from the transmission tunnel to the driver's side floor is starting to rot out. It's about a 3-4 hole. Did you purchase a piece to fix your floor or just shape your own?
  4. N

    I need them gone,...

    Wasn't really looking for it but rather than let it just go to scrap I might have an experiment to try with it However, CarID.com has them new for $103, including shipping. So if you want to mess with it for scrap/ship price let me know. I am in Montana, 59864. If not, no problem.
  5. N

    I need to make room for more stuff.

    Well, if it scrap status then I might be interested in the front mount receiver. I wasn't really "looking" for one, but to try an experiment I would consider it. Better than just throwing it away. Delivered new they are only $103 on CarID.com. I don't mind giving a little for it, just to try...
  6. N

    Snatch block recommendation

    I purchased a snatch block on the interweb and when it arrived I was not pleased with the slop around the pin, etc. It went back. I had never purchased one previously and wished that I would have asked first. So now I am looking for recommendations for a good one. Here's what it has to...
  7. N

    Using a high low adapter

    Just read about a Warn winch that was installed upside down in a TrailReady bumper (installed by TrailReady - not a hack job). What would stop me from running the winch I have upside down? It will fit no problem that way. Then I could keep the spare arm closed and out of the way. Sending an...
  8. N

    Using a high low adapter

    Thank you for the feedback. Both the front and rear are custom bumpers and are integrated into the frame strong enough in multiple areas that being ripped off isn't any more of a concern than a winch bumper would pose. The receivers in the bumpers are in no danger of being pulled apart...
  9. N

    Using a high low adapter

    I have a bumper with a swing out tire carrier on it. The bumper also has a hitch receiver under it. I just purchased a winch and cradle so that I can use it at either end of the XJ. Now, the problem is that in order for the winch to clear the rear tire, without having to swing it out of the...
  10. N

    Quick wiring question

    I just checked my 96 and the AC wire on mine is dark blue, single wire. It goes into the connector and comes out as 2 black wires which then go to different points on the compressor. On the diagrams that were linked it only shows that there should be a blue/white wire and no double blacks. I...
  11. N

    ISO Coolant reservoir cap part number

    Parts arrived today and here are the results: Crown automotive J3223202 (Mopar Coolant Bottle Cap) reservoir cap will snap on as long as the extra filler nozzle is removed. I really don't know why it is there in the first place. Snug and feels secured. CH3110103 is the right fan shroud for...
  12. N

    ISO Coolant reservoir cap part number

    I ordered mine from Morris. The generic part number for the shroud that seems to pop up all over is CH3110103 and OEM 52027762. So I will post my success on this and the coolant cap for anyone else looking will know.
  13. N

    Air filter recommendation

    Thanks for your suggestions. I purchased a Wix one today. I didn't know paper was so well thought of.
  14. N

    Air filter recommendation

    I have an 86 XJ w/ the 3.4L conversion I put in a few years back. It sports the Holley 4160 carb and Edelbrock intake 3789/3785. It has a round air cleaner assembly with a 14x3 inch filter. Previously I used a K&N and also a paper filter. It's 90% off highway use. In order to fit the filter...
  15. N

    ISO Coolant reservoir cap part number

    Well, AMC wasn't exactly "clean" in what they did during those years, either. However, I didn't know about the GM shenanigans, either. Whoever would give the cheapest price got the deal. I bought a rolled 88 XJ and the NP231 that was in it had the same input as the NP205 so I just did a...
Back
Top